Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2018.06
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1AAF  Heater Activation Relay Open  


DESCRIPTION

The pre-crash safety city sensor turns the pre-crash safety city heater on and off by operating the TSS C HTR relay.

When the pre-crash safety city sensor detects a malfunction in the TSS C HTR relay coil side circuit, C1AAF is output.

DTC Code DTC Detection Condition Trouble Area
C1AAF
Either of the following conditions is met:
·

When the pre-crash safety city heater receives an operation request, the BUZ terminal voltage of the pre-crash safety city sensor is continuously 1.368 V or higher for 5 seconds or more

·

When the pre-crash safety city heater receives a non-operation request, the BUZ terminal voltage of the pre-crash safety city sensor is continuously 0.145V or higher for 5 seconds or more


·

TSS C HTR relay

·

Harness or connector

·

Pre-crash safety city sensor



HINT:

Refer to SYSTEM DESCRIPTION "OUTLINE OF PRE-CRASH SAFETY CITY HEATER" for details about the pre-collision safety city heater operating conditions (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>SYSTEM DESCRIPTION).


WIRING DIAGRAM

E397706E03
0.281,2.052 1.24,2.479 0.958,0.427 10 false from IG1 NO. 1 Relay 1.708,2.25 2.677,2.448 0.969,0.198 10 false GAUGE 2.531,4.604 2.771,4.792 0.24,0.188 10 false IG 2.375,4.115 2.823,4.313 0.448,0.198 10 false GND 2.781,4.094 2.99,4.292 0.208,0.198 10 false 2 2.771,4.604 2.979,4.802 0.208,0.198 10 false 1 2.469,2.51 3.771,2.865 1.302,0.354 10 false Diode (TSS_C_RP) 3.771,1.552 5.271,1.781 1.5,0.229 10 false Diode (TSS_C_FW) 1.604,5.323 2.958,5.688 1.354,0.365 10 false Pre-crash Safety City Heater Wire 0.396,5.156 1.479,5.635 1.083,0.479 10 false Pre-crash Safety City Heater 3.948,2.917 5.781,3.427 1.833,0.51 10 false TSS C HTR 4.677,1.969 4.885,2.167 0.208,0.198 10 false 2 3.792,1.948 4,2.146 0.208,0.198 10 false 1 3.792,2.448 4,2.646 0.208,0.198 10 false 3 4.688,2.448 4.896,2.646 0.208,0.198 10 false 5 6.24,3.427 6.667,3.646 0.427,0.219 10 false SPR 5.76,3.927 7.094,4.354 1.333,0.427 10 false Pre-crash Safety City Sensor 5.76,3.76 6.125,3.969 0.365,0.208 10 false L11 6.021,3.26 6.229,3.458 0.208,0.198 10 false 1 6.031,1.938 6.24,2.135 0.208,0.198 10 false 8 6.25,2.052 6.698,2.24 0.448,0.188 10 false BUZ 1.604,5.115 1.948,5.313 0.344,0.198 10 false L12 1.625,4.615 1.833,4.813 0.208,0.198 10 false A 1.635,4.115 1.844,4.313 0.208,0.198 10 false B 0.125,6.271 2.104,6.479 1.979,0.208 10 false A: Terminal (Wiring Color "R") 2.344,6.271 4.448,6.5 2.104,0.229 10 false B: Terminal (Wiring Color "W-B") 3.781,1.396 4.188,1.594 0.406,0.198 10 false F143 2.469,2.344 2.875,2.542 0.406,0.198 10 false F142 3.667,4.906 4.125,5.104 0.458,0.198 10 false A/C 4.625,4.698 6.354,4.969 1.729,0.271 10 false from IG1 NO. 1 Relay 2.594,1.958 2.802,2.156 0.208,0.198 10 false 1 4.552,1.01 4.76,1.208 0.208,0.198 10 false 1 3.948,1.01 4.24,1.177 0.292,0.167 10 false 2 3.219,1.948 3.51,2.115 0.292,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.


·

When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.


·

When replacing the pre-crash safety city sensor with a new one, or performing removal, installation or replacement of the windshield glass, always perform "Recognition Camera/ Target Position Memory" and "Beam Axis Learning".

Perform adjustment with either "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY HEATER POWER SOURCE CIRCUIT)
a.
E363926C06
1.448,0.167 1.948,0.417 0.5,0.25 1.083,1.833 1.438,1.438 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.563,0.198 1.875,0.438 0.313,0.24 10 false L11 0.844,1.854 1.323,2.094 0.479,0.24 10 false BUZ
*a Front view of wire harness connector
(to Pre-crash Safety City Sensor)


Disconnect the pre-crash safety city sensor connector.

NOTICE:

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L11-8 (BUZ) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

2.CHECK HARNESS AND CONNECTOR (DIODE (TSS_C_FW) CIRCUIT)

NG

3.INSPECT TSS C HTR RELAY
2.CHECK HARNESS AND CONNECTOR (DIODE (TSS_C_FW) CIRCUIT)
a.

Remove the TSS C HTR relay.


b.
E363926C07
1.448,0.167 1.948,0.417 0.5,0.25 1.083,1.833 1.438,1.438 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.563,0.198 1.875,0.438 0.313,0.24 10 false L11 0.844,1.854 1.323,2.094 0.479,0.24 10 false BUZ
*a Front view of wire harness connector
(to Pre-crash Safety City Sensor)


Disconnect the pre-crash safety city sensor connector.

NOTICE:

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L11-8 (BUZ) - Body ground Ignition switch ON Below 1 V




OK

REPLACE PRE-CRASH SAFETY CITY SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DIODE (TSS_C_FW) CIRCUIT)

3.INSPECT TSS C HTR RELAY
a.

Remove the TSS C HTR relay.


b.

Inspect the TSS C HTR relay (See page Vehicle Interior>PRE-CRASH SAFETY>RELAY>ON-VEHICLE INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TSS C HTR RELAY COIL CIRCUIT)

NG

REPLACE TSS C HTR RELAY