Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0128    Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)


DESCRIPTION

HINT:
This DTC relates to the thermostat.

This DTC is stored when the Engine Coolant Temperature (ECT) does not reach 75°C (167°F) despite sufficient engine warm-up time having elapsed.

DTC No.
DTC Detection Condition
Trouble Area
P0128
  1. Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic):
  2. (a) Cold start
  3. (b) Engine warmed up
  4. (c) ECT less than 75°C (167°F)
  1. Thermostat
  2. Cooling system
  3. ECT sensor
  4. Wire harness or connector
  5. ECM

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed To
    DTC P0128 is output
    A
    P0128 and P0115, P0117, or P0118
    B



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the values displayed on the Techstream while wiggling the ECM wire harness.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result  
    Result
    Proceed to
    Value in Data List changes when wire harness is wiggled, or DTC is output*
    B
    Other than above
    A
    *: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).

    HINT:
    Check that the actual engine coolant temperature and the Coolant Temp value displayed on the Techstream are approximately equal. If the Coolant Temp value is lower than the actual, check the connector connections between the ECM and the engine coolant temperature sensor.



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A


3.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK


4.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat.

    Standard:
    80°C to 84°C (176°F to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT (Click here)
OK


5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPLACE ECM (Click here)