CAN COMMUNICATION SYSTEM (for Hatchback) > Check CAN Bus Line for Short to GND |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. |
|


| 1.CHECK SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
Turn the ignition switch off.
Disconnect the A73 and D146 No. 1 junction connectors.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D102-6 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D102-14 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 2.CONNECT CONNECTOR |
Reconnect the A73 and D146 No. 1 junction connectors.
| NEXT | |
| 3.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR) |
Disconnect the D147 No. 2 junction connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D102-6 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D102-14 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 4.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-7 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-18 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 5.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-8 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-19 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
| OK | A |
| NG (w/ Cooler) | B |
| NG (w/o Cooler) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-1 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-12 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 7.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-4 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-15 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 8.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Disconnect the A73 and D146 No. 1 junction connectors.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D146-4 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D146-15 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 9.CONNECT CONNECTOR |
Reconnect the D147 No. 2 junction connector.
| NEXT | |
| 10.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A73-9 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-20 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 11.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A73-10 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-21 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 12.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D146-2 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D146-13 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 13.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D146-1 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D146-12 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 14.CHECK SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE) |
Disconnect the D100 combination meter assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-7 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-18 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 15.CHECK SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE) |
Disconnect the D130 air conditioning amplifier assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-8 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-19 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 16.CHECK SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE) |
Disconnect the D122 steering angle sensor (spiral cable sub-assembly) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-1 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-12 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 17.CHECK SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
Disconnect the D112 airbag sensor assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D147-4 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D147-15 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 18.CHECK SHORT TO GND IN CAN BUS WIRE (ECM MAIN WIRE) |
Disconnect the A72 ECM connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A73-9 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-20 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 19.CHECK SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE) |
Disconnect the A70*1 or A71*2 skid control ECU (brake actuator assembly) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A73-10 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| A73-21 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
| NG | A |
| OK (w/ VSC) | B |
| OK (w/o VSC) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 20.CHECK SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY) |
Disconnect the D104 power steering ECU assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D146-2 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D146-13 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 21.CHECK SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE) |
Disconnect the D143 main body ECU (multiplex network body ECU) connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D146-1 (CANH) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| D146-12 (CANL) - D102-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||