Refer to DTC P0031.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0031
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0134 | Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1) | Heated oxygen sensor (sensor 1) output does not indicate rich (higher than 0.45 V) even once when conditions (a), (b), (c), (d) and (e) continue for more than 50 seconds (1 trip detection logic):
(a) Engine speed: 1400 rpm or more (b) Vehicle speed: 40 km/h (24 mph) or more (c) Throttle valve not fully closed (d) 180 seconds or more after starting engine (e) Engine coolant temperature more than 40°C (104°F) |
·
Open or short in heated oxygen sensor (sensor 1) circuit ·
Heated oxygen sensor heater (sensor 1) ·
Heated oxygen sensor (sensor 1) ·
Fuel pressure ·
Intake system ·
PCV hose connections ·
PCV valve and hose ·
Fuel injector assembly ·
Exhaust gas leakage ·
ECM |
Comes on | DTC stored |
If this DTC is stored, check the output voltage of the heated oxygen sensor (sensor 1) by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / O2S B1S1.
The ECM uses the heated oxygen sensor to optimize the air fuel mixture with closed loop fuel control. This control helps decrease exhaust emissions by providing the catalyst with a nearly stoichiometric mixture. The sensor detects the oxygen level in the exhaust gas and the ECM uses this data to control the air fuel ratio. The sensor output voltage range is from 0 V to 1 V. If the signal voltage is less than 0.45 V, the air fuel ratio is lean. If the signal voltage is higher than 0.45 V, the air fuel ratio is rich. If the sensor does not indicate rich at least once despite the conditions for the closed loop fuel control being met and the specified time period has passed, the ECM will conclude that the closed loop fuel control is malfunctioning. The ECM will illuminate the MIL and a DTC is stored.
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 1) |
| Required Sensors/Components (Related) | Engine coolant temperature sensor
Throttle body with motor assembly Crankshaft position sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Intrusive closed loop is performed when following conditions met | - |
| Duration that the following conditions met | 50 seconds |
| Engine coolant temperature | 40°C (104°F) or higher |
| Engine speed | 1400 rpm or higher |
| Vehicle speed | 40 km/h or higher |
| Idle | OFF |
| Battery voltage | 11 V or higher |
| Oxygen sensor voltage | Less than 0.45 V |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature reaches 40°C (104°F) or higher [B].
Drive the vehicle at 40 km/h (24 mph) or more for 4 minutes or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0134.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [D] again.
Refer to DTC P0031.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0031
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2.
Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).
Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
| GTS Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| O2S B1S1
(Heated oxygen sensor (sensor 1)) |
12.5% | Rich | Higher than 0.5 V |
| -12.5% | Lean | Below 0.4 V | |
| O2S B1S2
(Heated oxygen sensor (sensor 2)) |
12.5% | Rich | Higher than 0.5 V |
| -12.5% | Lean | Below 0.4 V |
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors.
To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2, and then press the graph button on the Data List view.
Inspect the fuses for circuits related to this system before performing the following procedure.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0134 is output | A |
| DTC P0134 and other DTCs are output | B |
If any DTCs other than P0134 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed and O2S B1S1.
| Tester Display |
|---|
| Engine Speed |
| O2S B1S1 |
Warm up the engine until the engine coolant temperature reaches higher than 40°C (104°F).
Rev the engine up to 4000 rpm 3 times using the accelerator pedal.
Read the output voltage of the heated oxygen sensor (sensor 1) displayed on the GTS when the engine speed is suddenly increased.
Heated oxygen sensor voltage output indicates 0.45 V or higher (rich signal) at least once.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the PCV hose connections.
Click hereEngine / Hybrid System>2NZ-FE EMISSION CONTROL>PCV VALVE>COMPONENTS
PCV hose is connected correctly and is not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the heated oxygen sensor (sensor 1).
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1)) |
Disconnect the heated oxygen sensor (sensor 1) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B24-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B24 heated oxygen sensor (sensor 1) connector.
Disconnect the B30 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B24-1 (HT1A) - B30-8 (HT1A) | Always | Below 1 Ω |
| B24-3 (OX1A) - B30-19 (OX1A) | Always | Below 1 Ω |
| B24-4 (E2) - B30-20 (EX1A) | Always | Below 1 Ω |
| B24-1 (HT1A) or B30-8 (HT1A) - Body ground | Always | 10 kΩ or higher |
| B24-3 (OX1A) or B30-19 (OX1A) - Body ground | Always | 10 kΩ or higher |
| B24-4 (E2) or B30-20 (EX1A) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leakage from intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure.
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leak.
No gas leak.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B24 heated oxygen sensor (sensor 1) connector.
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B24-2 (+B) - 2H-4 | Always | Below 1 Ω |
| B24-2 (+B) or 2H-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0134 is output | B |
A
B
Has the vehicle run out of fuel in the past?
| Proceed to |
|---|
| YES |
| NO |
YES
NO