1.INSPECT COOLANT
2.INSPECT ENGINE OIL
3.INSPECT BATTERY
17801
4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner cap with No. 1 air cleaner hose.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL
Remove the air cleaner filter element sub-assembly.
Visually check that there is no dirt, blockage, or damage to the air cleaner filter element sub-assembly.
If there is any dirt or a blockage in the air cleaner filter element sub-assembly, clean it with compressed air.
If any dirt or a blockage remains even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.
Install the air cleaner filter element sub-assembly.
Install the air cleaner cap with No. 1 air cleaner hose.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>THROTTLE BODY>INSTALLATION
16361A
5.INSPECT FAN AND GENERATOR V BELT
19100P
6.INSPECT SPARK PLUG
7.INSPECT IGNITION TIMING
When using the GTS:
Warm up the engine.
Turn all the electrical systems and the A/C off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus:
Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
| Tester Display |
|---|
| IGN Advance |
Inspect the ignition timing at idle.
| Transaxle | Ignition Timing |
|---|---|
| Manual Transaxle | 8 to 12 degrees BTDC |
| Automatic Transaxle |
Inspect the ignition timing with the cooling fan off.
When checking the ignition timing, shift the transaxle to the neutral position.
Enter the following menus:
Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / OFF.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
When not using the GTS:
Remove the No. 2 cylinder head cover.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>REMOVAL
Pull out the wire harness (brown) shown in the illustration.
After checking, wrap the wire harness with tape.
Warm up the engine.
Turn all the electrical systems and the A/C off.
Turn the ignition switch off.
Connect the clip of the timing light to the wire harness (brown).
Use a timing light that detects the first signal.
| *1 | DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Start the engine.
Inspect the ignition timing at idle.
| Transaxle | Ignition Timing |
|---|---|
| Manual Transaxle | 8 to 12 degrees BTDC |
| Automatic Transaxle |
Inspect the ignition timing with the cooling fan off.
When checking the ignition timing, shift the transaxle to the neutral position.
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSTALLATION
Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.
8.INSPECT ENGINE IDLING SPEED
When using the GTS:
Warm up the engine.
Turn all the electrical systems and the A/C off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Inspect the engine idle speed.
| Transaxle | Idling Speed |
|---|---|
| Manual Transaxle | 600 to 700 rpm |
| Automatic Transaxle | 650 to 750 rpm |
Inspect the engine idling speed with the cooling fan off.
When checking the engine idling speed, shift the transaxle to the neutral position or the park position.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
When not using the GTS.
Warm up the engine.
Turn all the electrical systems and the A/C off.
Turn the ignition switch off.
| *1 | DLC3 |
Using SST, connect terminal 9 (TAC) of the DLC3.
Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Connect a tachometer.
Start the engine.
Inspect the engine idle speed.
| Transaxle | Idling Speed |
|---|---|
| Manual Transaxle | 600 to 700 rpm |
| Automatic Transaxle | 650 to 750 rpm |
Inspect the engine idling speed with the cooling fan off.
When checking the engine idling speed, shift the transaxle to the neutral position or the park position.
Turn the ignition switch off.
Disconnect the tachometer.
Disconnect SST from terminal 9 (TAC) of the DLC3.
9.INSPECT VALVE CLEARANCE
10.INSPECT COMPRESSION
Warm up and stop the engine.
Remove the 4 spark plugs.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Disconnect the 4 fuel injector assembly connectors.
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
980 kPa (10.0 kgf/cm2, 142 psi)
784 kPa (8.0 kgf/cm2, 114 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
Inspect the other cylinders in the same way.
Measure the compression in as short a time as possible.
If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.
If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.
Connect the 4 fuel injector assembly connectors.
Install the 4 spark plugs.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
Clear the DTC.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
11.INSPECT CO/HC
Warm up the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2500 rpm.
When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the heated oxygen sensor (for Sensor 1) operation.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>INSPECTION
Check the heated oxygen sensor (for Sensor 2) operation.
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 2)>INSPECTION
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
|---|---|---|---|
| Normal | High | Rough idling | 1.
Faulty ignition: ·
Incorrect timing ·
Fouled, shorted or improperly gapped plugs 2.
Incorrect valve clearance 3.
Leakage from intake and exhaust valves 4.
Leakage from cylinders |
| Low | High | Rough idling
(Fluctuating HC reading) |
1.
Vacuum leaks: ·
PCV hoses ·
Intake manifold ·
Throttle body with motor assembly ·
Brake booster line 2.
Lean mixture causing misfire |
| High | High | Rough idling
(Black smoke from exhaust) |
1.
Restricted air cleaner filter element sub-assembly 2.
Plugged PCV valve 3.
Faulty EFI systems: ·
Faulty fuel pressure regulator assembly ·
Faulty engine coolant temperature sensor ·
Faulty mass air flow meter ·
Faulty ECM ·
Faulty fuel injector assembly ·
Throttle body with motor assembly |