1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3.REMOVE FRONT WHEEL RH
4.DRAIN ENGINE OIL
5.DRAIN ENGINE COOLANT
58910C
6.REMOVE REAR CONSOLE BOX ASSEMBLY
57533B
7.REMOVE FRONT FLOOR CENTER BRACE
17410
8.REMOVE FRONT EXHAUST PIPE ASSEMBLY
51441C
9.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
51451A
10.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
51405A
11.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
27060
12.REMOVE GENERATOR WITH REGULATOR ASSEMBLY
19500D
13.REMOVE NO. 1 IGNITION COIL
12261
14.DISCONNECT VENTILATION HOSE
23820
15.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
11201
16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
12305
17.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
| *a | Wooden Block |
Place a wooden block on a jack underneath the engine assembly.
Remove the 4 bolts, 2 nuts and engine mounting insulator sub-assembly RH from the engine mounting bracket RH and vehicle.
13407
18.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY
Set the No. 1 cylinder to TDC/compression.
| *a | Timing Notch |
| *b | Timing Mark "0" |
Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump assembly.
| *a | Timing Mark |
Check that the timing marks on the camshaft timing sprocket and camshaft timing gear assembly are facing upward as shown in the illustration.
If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.
| *a | Hold |
| *b | Turn |
Using SST, loosen the bolt of the crankshaft damper sub-assembly.
Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.
Remove SST from the crankshaft damper sub-assembly.
Remove the bolt and crankshaft damper sub-assembly from the crankshaft.
15100Q
19.REMOVE CRANKSHAFT POSITION SENSOR
11101J
20.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
16173
21.REMOVE WATER PUMP PULLEY
16100
22.REMOVE ENGINE WATER PUMP ASSEMBLY
12315A
23.REMOVE ENGINE MOUNTING BRACKET RH
Remove the 4 bolts and engine mounting bracket RH from the oil pump assembly.
15100
24.REMOVE OIL PUMP ASSEMBLY
Remove the 16 bolts, nut and 2 wire harness clamp brackets from the oil pump assembly.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the oil pump assembly by prying between the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.
Do not damage the contact surfaces of the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.
Remove the 2 O-rings from the cylinder block sub-assembly and oil pan sub-assembly.
25.REMOVE TAPER SCREW PLUG
Using an 8 mm hexagon wrench, remove the taper screw plug from the oil pump assembly.
15100C
26.REMOVE OIL PUMP SEAL
| *a | Wooden Block |
| *b | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal from the oil pump assembly.