67862
1.INSTALL FRONT DOOR WEATHERSTRIP
Engage the 15 clips and install the front door weatherstrip.
Install the clip.
68610
2.INSTALL FRONT DOOR CHECK ASSEMBLY
Apply MP grease to the sliding parts of the front door check assembly.
| *a | Door Panel Side |
| *b | Body Panel Side |
Install the front door check assembly onto the door panel side with the 2 bolts.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the front door check assembly onto the body panel side with the bolt.
67001A
3.INSTALL FRONT DOOR PANEL CUSHION
Install the 2 front door panel cushions.
69312
4.INSTALL FRONT DOOR LOCK OPEN ROD
| *a | Snap Ring |
Install the front door lock open rod to the front door outside handle frame sub-assembly.
Engage the snap ring as shown in the illustration.
69202A
5.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/ Smart Entry and Start System)
Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly.
Engage the claw and the clamp, and connect the wire harness to the front door outside handle frame sub-assembly.
| *a | Guide |
| *b | Clamp |
Engage the guide and install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
Engage the clamp.
69202A
6.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/o Smart Entry and Start System)
Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly.
Engage the guide and install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
69242E
7.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD
Engage the 2 claws and install the front door outside handle rear pad.
69241H
8.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD
Engage the 2 claws and install the front door outside handle front pad.
69220
9.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Smart Entry and Start System)
69220
10.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Smart Entry and Start System)
Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.
69320
11.INSTALL FRONT DOOR LOCK ASSEMBLY (for TMT Made)
69320
12.INSTALL FRONT DOOR LOCK ASSEMBLY (for TMMIN Made)
w/ Power Door Lock
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>INSTALLATION
w/o Power Door Lock
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>INSTALLATION
13.INSTALL HOLE PLUG (for TMMIN Made)
w/o Power Door Lock
Install the hole plug.
69217F
14.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (w/ Lock Cylinder)
Engage the 2 claws and install the front door outside handle cover to the lock cylinder.
Apply MP grease to the sliding parts of the lock cylinder.
| *1 | Hole Plug |
Install the front door outside handle cover with lock cylinder.
Make sure that the lock cylinder is inserted into the front door lock assembly.
Using a T30 "TORX" socket wrench, tighten the screw.
Install the hole plug.
69217F
15.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (w/o Lock Cylinder)
| *1 | Hole Plug |
Engage the 2 claws and install the front door outside handle cover.
Using a T30 "TORX" socket wrench, tighten the screw.
Install the hole plug.
67404F
16.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Engage the guide and install the front door rear lower frame sub-assembly.
Install the 2 bolts.
67924
17.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION
| *a | Double-sided Tape |
Install a new front door No. 2 stiffener cushion with the 2 bolts.
Peel off the backing paper from the double-sided tape before installing the front door No. 2 stiffener cushion.
Apply thorough pressure to the sections with double-sided tape.
69820
18.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)
Apply MP grease to the sliding parts of the front door window regulator assembly.
| *a | Temporary Bolt |
Temporarily install the temporary bolt to the front door window regulator assembly.
Temporarily install the front door window regulator assembly.
Install the front door window regulator assembly with the 5 bolts and tighten the temporary bolt.
Connect the connector.
69820
19.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the front door window regulator assembly with the 5 bolts.
67664C
20.INSTALL DOOR FRAME GARNISH
Engage the clamp and install a new door frame garnish.
68151D
21.INSTALL FRONT DOOR GLASS RUN
Install the front door glass run.
68102
22.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
w/ Power Window:
Connect the power window regulator master switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly so that the door glass bolt holes can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power window regulator master switch assembly.
w/o Power Window:
Install the front door window regulator handle assembly.
Move the front door glass sub-assembly so that the door glass bolt holes can be seen.
Remove the front door window regulator handle assembly.
Insert the front door glass sub-assembly into the front door panel as indicated by the arrows in the order shown in the illustration.
Do not damage the front door glass sub-assembly.
Install the front door glass sub-assembly with the 2 bolts.
Do not damage the front door glass sub-assembly.
67832
23.INSTALL FRONT DOOR SERVICE HOLE COVER
Apply new butyl tape to the front door panel.
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
| *a | Reference Point |
Install the front door service hole cover according to the reference points on the front door panel.
Securely install the front door service hole cover, taking care to prevent wrinkles and air bubbles.
68172A
24.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP
Install the front door glass inner weatherstrip.
75732B
25.INSTALL FRONT DOOR OUTSIDE MOULDING (for Hatchback)
75922M
26.INSTALL NO. 1 BLACK OUT TAPE (w/ Black Out Tape)
75756C
27.INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING
68210C
28.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
87940
29.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY (w/ Power Mirror Adjust Function)
87940
30.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY (w/o Power Mirror Adjust Function)
86160
31.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
69206B
32.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 4 guides and install the front door inside handle sub-assembly to the front door trim board sub-assembly.
67602
33.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Front door inside locking cable assembly |
| *2 | Front door lock remote control cable assembly |
Engage the 2 guides and connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door trim board sub-assembly.
Engage the 5 claws and the guide.
Engage the 8 clips and install the front door trim board sub-assembly.
Install the 3 screws.
Engage the claw and close the door inside handle bezel plug.
74232
34.INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)
Connect the connector.
Engage the 9 claws and install the front armrest base upper panel.
74232
35.INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)
Engage the 7 claws and install the front armrest base upper panel.
69260
36.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
Install the front door window regulator handle assembly and fully open the front door glass sub-assembly.
Remove the front door window regulator handle assembly.
| *a | Door Panel Side |
| *b | Inside of Vehicle |
Install the window regulator handle plate as shown in the illustration.
| *a | Front of Vehicle |
| *b | Assemble with Glass in Fully Open Position |
Install the front door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.
67492A
37.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
Engage the 2 clips and install the front door lower frame bracket garnish.
38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (for Hatchback).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
39.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side with Power Window)
40.INSPECT POWER WINDOW OPERATION (w/ Power Window)