Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2014.03–2017.10
RM30M0E _59 Vehicle Exterior _017122 DOOR / HATCH _0087457 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


PROCEDURE

Hide 67872 1.INSTALL REAR DOOR WEATHERSTRIP

a.
B346771

Engage the clamp and the 16 clips, and install the rear door weatherstrip.


Hide 68630 2.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.
B346770C01
0.875,0.26 1.188,0.458 0.313,0.198 10 false *a 2.74,0.26 3.052,0.458 0.313,0.198 10 false *b
*a Door Panel Side
*b Body Panel Side


Install the rear door check assembly onto the door panel side with the 2 bolts.

Torque:
for TMT Made : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
for TMMIN Made : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install the rear door check assembly onto the body panel side with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69204A 3.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B346776C01
2.156,0.573 2.313,0.875 true 0.677,1.344 0.323,1.5 true 1.99,0.458 2.302,0.615 0.313,0.156 10 true *a 0.125,1.396 0.344,1.583 0.219,0.188 10 true *b
*a Grommet
*b Guide


Engage the guide and the grommet, and install the rear door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69242G 4.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B346768

Engage the 2 claws and install the rear door outside handle rear pad.


Hide 69241G 5.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B346767

Engage the 2 claws and install the rear door outside handle front pad.


b.
B346766

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69240 6.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B346777

Install the rear door outside handle assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69227L 7.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B346764

Engage the 2 guides and the 2 claws, and install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69340 8.INSTALL REAR DOOR LOCK ASSEMBLY (for TMT Made)

Hide 69340 9.INSTALL REAR DOOR LOCK ASSEMBLY (for TMMIN Made)

Hide 10.INSTALL HOLE PLUG (for TMMIN Made)

HINT:

w/o Power Door Lock


a.
B365427

Install the hole plug.


Hide 68189 11.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP

a.
B346763

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


Hide 68124B 12.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.
B346778

Install the rear door quarter window glass with rear door quarter window weatherstrip in the direction indicated by the arrow as shown in the illustration.


Hide 69840A 13.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.
B346761C01
1.646,0.729 1.802,0.698 true 1.823,0.583 2.135,0.76 0.313,0.177 10 false *a
*a Temporary Bolt


Temporarily install the temporary bolt to the rear door window regulator assembly.


c.

Temporarily install the rear door window regulator assembly.


d.

Install the rear door window regulator assembly with the 3 bolts and tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69840A 14.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)

a.
B347103

Install the rear door window regulator assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68104 15.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B346779

Insert the rear door glass sub-assembly into the rear door panel in the direction indicated by the arrow as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



b.
B346780

Install the rear door glass sub-assembly to the rear door window regulator assembly as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



Hide 67408H 16.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B346758

Install the screw.

NOTICE:

Make sure to return the rear door weatherstrip to its original condition after performing this step.


HINT:

Peel back the rear door weatherstrip to install the screw.



b.

Install the rear door window division bar sub-assembly with the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)

NOTICE:

When installing rear door window division bar sub-assembly, do not allow the rear door quarter window glass to fall.



Hide 67842E 17.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.

Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.


c.
B346781C01
0.469,0.396 0.563,0.302 false 2.854,0.406 2.75,0.302 false 0.552,0.167 0.865,0.323 0.313,0.156 10 false *a 2.615,0.208 2.927,0.365 0.313,0.156 10 false *a
*a Reference Point


Install the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover, taking care to prevent wrinkles and air bubbles.



d.

Connect each connector.


Hide 67674A 18.INSTALL REAR DOOR FRAME GARNISH

a.
B346755

Engage the clamp and install a new rear door frame garnish.


Hide 68152C 19.INSTALL REAR DOOR GLASS RUN

a.
B346756

Install the rear door glass run.


Hide 68174A 20.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B346754

Install the rear door glass inner weatherstrip.


Hide 75742 21.INSTALL REAR DOOR OUTSIDE MOULDING (for Hatchback)

Hide 75924 22.INSTALL NO. 2 BLACK OUT TAPE (for Sedan)

Hide 75924 23.INSTALL NO. 2 BLACK OUT TAPE (for Hatchback)

Hide 75762A 24.INSTALL REAR DOOR WINDOW FRAME FRONT MOULDING

Hide 68230C 25.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 86160B 26.INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 69206C 27.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B346753

Engage the 4 guides and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


Hide 67604 28.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B356963C01
1.521,0.688 1.427,0.417 true 1.219,1.156 1.417,0.958 false 1.354,0.26 1.667,0.458 0.313,0.198 10 false *1 1.083,1.188 1.396,1.385 0.313,0.198 10 false *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


Engage the 2 guides and connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door trim board sub-assembly.


b.
B346751

Engage the 6 claws and the guide.


c.

Engage the 7 clips and install the rear door trim board sub-assembly.


d.
B346748

Install the 3 screws.


e.
B347470

Engage the claw and close the door inside handle bezel plug.


Hide 74272A 29.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)

a.
B346746

Connect the connector.


b.
B346745

Engage the 7 claws and install the rear door armrest base upper panel.


Hide 74272A 30.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)

a.
B347101

Engage the 5 claws and install the rear door armrest base upper panel.


Hide 69260E 31.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.

Install the rear door window regulator handle assembly and fully open the rear door glass sub-assembly.


b.

Remove the rear door window regulator handle assembly.


c.
B346721C01
2.333,0.542 2.646,0.74 0.313,0.198 10 false *a 2.906,0.542 3.094,0.74 0.188,0.198 10 false *b
*a Door Panel Side
*b Inside of Vehicle


Install the window regulator handle plate as shown in the illustration.


d.
B346725C01
3.01,0.896 3.323,1.094 0.313,0.198 10 false *a 0.521,1.063 0.833,1.26 0.313,0.198 10 false 0° 1.01,0.125 1.469,0.323 0.458,0.198 10 false 60° 0.667,0.5 0.979,0.698 0.313,0.198 10 false *b
*a Front of Vehicle
*b Assemble with Glass in Fully Open Position


Install the rear door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.


Hide 32.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (for Hatchback).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION