In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the body computer may be malfunctioning.
When replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
Troubleshooting should be started after confirming that the customize status of the wireless door lock buzzer answer-back function has been switched on.
Before performing the inspection, check that DTC B27B0 (Smart Entry and Start System) is not output.
Check the wireless door lock control function using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Wireless door lock/unlock operates properly (for TMT Made) | A |
| Wireless door lock/unlock operates properly (for TMMIN Made) | B |
| Wireless door lock/unlock does not operate properly | C |
A
B
C
for LHD
Remove the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>REMOVAL
Inspect the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>INSPECTION
for RHD
Remove the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>REMOVAL
Inspect the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the H3 front door lock assembly LH connector.
for RHD
Disconnect the G2 front door lock assembly RH connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-8 (LSSR) - F52-15 (LSWD) | Always | Below 1 Ω |
| H3-7 (E) - Body ground | Always | Below 1 Ω |
| H3-8 (LSSR) or F52-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-7 (LSSR) - F52-15 (LSWD) | Always | Below 1 Ω |
| G2-8 (E) - Body ground | Always | Below 1 Ω |
| G2-7 (LSSR) or F52-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wireless answer-back operation using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Only wireless door lock buzzer answer-back does not occur. | A |
| Only hazard warning light answer-back does not occur. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B
Disconnect the A30 wireless door lock buzzer connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-1 (B) - F43-2 (BZR) | Always | Below 1 Ω |
| A30-2 (E) - Body ground | Always | Below 1 Ω |
| A30-1 (B) or F43-2 (BZR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the wireless door lock buzzer with a new one.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B
Replace the body computer with a new one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the wireless answer-back function.
Wireless answer-back function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the hazard warning lights blink when the hazard warning signal switch is pressed.
Hazard warning lights blink.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F39 combination meter assembly connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F39-3 (HAZ) - F52-6 (HAZ) | Always | Below 1 Ω |
| F39-3 (HAZ) or F52-6 (HAZ) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Remove the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>REMOVAL
Inspect the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>INSPECTION
for RHD
Remove the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>REMOVAL
Inspect the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the H3 front door lock assembly LH connector.
for RHD
Disconnect the G2 front door lock assembly RH connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-8 (LSSR) - F52-15 (LSWD) | Always | Below 1 Ω |
| H3-7 (E) - Body ground | Always | Below 1 Ω |
| H3-8 (LSSR) or F52-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-7 (LSSR) - F52-15 (LSWD) | Always | Below 1 Ω |
| G2-8 (E) - Body ground | Always | Below 1 Ω |
| G2-7 (LSSR) or F52-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wireless answer-back operation using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Only wireless door lock buzzer answer-back does not occur. | A |
| Only hazard warning light answer-back does not occur. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B
Disconnect the A30 wireless door lock buzzer connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-1 (B) - F43-2 (BZR) | Always | Below 1 Ω |
| A30-2 (E) - Body ground | Always | Below 1 Ω |
| A30-1 (B) or F43-2 (BZR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the wireless door lock buzzer with a new one.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer Operation |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B
Replace the body computer with a new one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the wireless answer-back function.
Wireless answer-back function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the hazard warning lights blink when the hazard warning signal switch is pressed.
Hazard warning lights blink.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F39 combination meter assembly connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F39-3 (HAZ) - F52-6 (HAZ) | Always | Below 1 Ω |
| F39-3 (HAZ) or F52-6 (HAZ) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG