Home › Engine / Hybrid System › 2NR-FE COOLING › RADIATOR › 2016.04–2016.07
RM30M0E _51 Engine / Hybrid System _053565 2NR-FE COOLING _0259971 RADIATOR A

2NR-FE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16561 1.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

HINT:

This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.


a.
A383331E01
0.24,0.031 1.688,0.344 1.448,0.313 10 false 22.1 mm (0.87 in.)

Install the No. 1 radiator to support seal for upper side to the radiator assembly.

HINT:

Make sure that the No. 1 radiator to support seal does not overlap onto the radiator core plate.



b.
A383332E01
0.313,1.979 2.76,2.177 2.448,0.198 10 false 25 mm (0.98 in.)

Install the No. 1 radiator to support seal for lower side to the radiator assembly.

HINT:

Make sure that the No. 1 radiator to support seal does not overlap onto the radiator core plate.



Hide 2.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install the radiator drain cock plug to the radiator assembly.

NOTICE:

Replace the O-ring if it is damaged.



Hide 16535 3.INSTALL LOWER RADIATOR SUPPORT

a.

Install the 2 lower radiator supports to the radiator assembly.


Hide 16523A 4.INSTALL RADIATOR SUPPORT CUSHION

a.

Install the 2 radiator support cushions to the radiator assembly.


Hide 16711 5.INSTALL FAN SHROUD

A381287

a.

Engage the 3 guides and 2 claws to install the fan shroud to the radiator assembly.


Hide 16400 6.INSTALL RADIATOR ASSEMBLY (w/ Cooler System)

a.
A313071

Install the radiator assembly together with fan shroud to the vehicle.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.



b.
A313088

Engage the 2 guides and 2 claws to connect the cooler condenser assembly to the radiator assembly.

HINT:

While tilting the cooler condenser assembly toward the front of the vehicle, install the cooler condenser assembly to the radiator assembly.



c.

Engage the 3 clamps to connect the wire harness to the fan shroud.


d.

Connect the cooling fan motor connector.


Hide 16400 7.INSTALL RADIATOR ASSEMBLY (w/o Cooler System)

a.
A313071

Install the radiator assembly together with fan shroud to the vehicle.


b.

Engage the 3 clamps to connect the wire harness to the fan shroud.


c.

Connect the cooling fan motor connector.


Hide 16572D 8.CONNECT NO. 2 RADIATOR HOSE

a.
A313073C01
1.927,3.167 1.51,2.99 false 2.177,0.063 2.333,0.26 0.156,0.198 10 false A 0.427,1.906 0.74,2.104 0.313,0.198 10 false *a 1.979,3.115 2.292,3.313 0.313,0.198 10 false *b 1.542,2.052 1.854,2.25 0.313,0.198 10 false *c 1.969,2.625 2.281,2.823 0.313,0.198 10 false *d
*a View A
*b Hose Paint Mark
*c Front of Vehicle
*d Right Side of Vehicle


Connect the No. 2 radiator hose to the radiator assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 2 radiator hose and hose clip at the correct angle.



Hide 16571C 9.CONNECT NO. 1 RADIATOR HOSE

a.
A382351C01
1.01,3.094 1.344,2.813 false 0.49,1.917 0.802,2.115 0.313,0.198 10 false *a 1.542,1.896 1.854,2.094 0.313,0.198 10 false *c 1.823,2.031 2.135,2.229 0.313,0.198 10 false 60° 0.958,2.573 1.271,2.771 0.313,0.198 10 false *d 0.844,3.031 1.156,3.229 0.313,0.198 10 false *b 2.396,1.313 2.708,1.51 0.313,0.198 10 false A
*a View A
*b Hose Paint Mark
*c Top of Vehicle
*d Left Side of Vehicle


Connect the No. 1 radiator hose to the radiator assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 1 radiator hose and hose clip at the correct angle.



Hide 10.CONNECT RADIATOR RESERVOIR TANK HOSE

a.

Connect the radiator reservoir tank hose to the radiator assembly.


Hide 53216A 11.INSTALL UPPER RADIATOR SUPPORT

a.

Install the upper radiator support to the radiator support assembly with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the low pitched horn assembly connector.


c.

Engage the 3 clamps to connect the wire harness to the upper radiator support.


d.

Engage the clamp to connect the hood lock control cable assembly to the upper radiator support.


Hide 89173 12.INSTALL FRONT AIRBAG SENSOR (w/ Airbag System)

Hide 53215B 14.INSTALL HOOD LOCK SUPPORT

a.

Install the hood lock support to the radiator support assembly with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Engage the clamp to connect the wire harness to the hood lock support.


Hide 81150 16.INSTALL HEADLIGHT ASSEMBLY LH

Hide 81150 17.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 20.ADJUST HOOD SUB-ASSEMBLY