Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › CAMSHAFT › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091001 CAMSHAFT A

1NZ-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13050 1.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13511 2.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft and camshaft journals.


b.
A116220C01
1.74,1 1.615,0.406 true 0.417,0.813 1.656,1.063 true 1.49,0.24 1.646,0.417 0.156,0.177 10 false *a 0.167,0.74 0.333,0.917 0.167,0.177 10 false *b
*a Paint Mark
*b Timing Mark


Install the chain sub-assembly to the camshaft timing gear assembly with the paint mark and timing mark aligned as shown in the illustration.


c.
A302799E01
0.729,1.938 0.885,2.135 0.156,0.198 10 false 3 1.365,1.938 1.521,2.135 0.156,0.198 10 false 1 2.042,1.938 2.198,2.135 0.156,0.198 10 false 2 2.708,1.938 2.865,2.135 0.156,0.198 10 false 4

Examine the front marks and numbers on 4 No. 2 camshaft bearing caps and check that the sequence is as shown in the illustration. Then uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



Hide 13512 3.INSTALL NO. 2 CAMSHAFT

a.

Apply a light coat of engine oil to the No. 2 camshaft and camshaft journals.


b.
A310640

Install the No. 2 camshaft to the cylinder head sub-assembly.


c.
A305918C01
1.208,1.792 1.208,0.906 true 1.292,0.531 1.125,0.219 true 1.271,0.635 0.25,1.313 true 0.917,0.083 1.229,0.24 0.313,0.156 10 false *a 0.052,1.24 0.365,1.396 0.313,0.156 10 false *b 1.115,1.823 1.427,1.979 0.313,0.156 10 false *c
*a Paint Mark
*b Timing Mark
*c Straight Pin


Hold the chain sub-assembly, and align the timing mark on the camshaft timing sprocket with the paint mark of the chain sub-assembly.


d.

Align the alignment pin hole in the camshaft timing sprocket with the straight pin of the No. 2 camshaft, and install the camshaft timing sprocket to the No. 2 camshaft.


e.
A305657

Temporarily install the flange bolt to the camshaft timing sprocket.


f.
A142357C01
0.167,1.229 0.594,1.427 0.427,0.198 10 false 5 (*1) 0.865,0.448 1.292,0.635 0.427,0.188 10 false 3 (*2) 1.531,0.448 1.906,0.646 0.375,0.198 10 false 1 (*2) 2.229,0.448 2.604,0.625 0.375,0.177 10 false 2 (*2) 2.844,0.448 3.229,0.646 0.385,0.198 10 false 4 (*2)
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap


Examine the front marks and numbers of the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps and check that the sequence is as shown in the illustration. Then uniformly tighten the 11 bolts in several steps in the sequence shown in the illustration.

Torque:
No. 1 Camshaft Bearing Cap : 23 N*m (235 kgf*cm, 17 ft.*lbf)
No. 2 Camshaft Bearing Cap : 15.4 N*m (157 kgf*cm, 11 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the No. 2 camshaft level.



g.
A305309C01
1.396,1.677 1.521,1.229 true 1.323,1.719 1.635,1.875 0.313,0.156 10 false *a 2.469,0.167 2.781,0.323 0.313,0.156 10 false *b 1.115,0.083 1.427,0.24 0.313,0.156 10 false *c
*a 14 mm Union Nut Wrench
*b Hold
*c Turn


Using a 14 mm union nut wrench, hold the hexagonal lobe of No. 2 camshaft and tighten the flange bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

HINT:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



h.

Remove the 3 mm (0.12 in.) diameter bar from the stopper plate.


i.
A116203C02
2.146,1.042 2.406,1.948 true 2.26,1.01 2.688,1.927 true 2.365,1.979 2.531,2.156 0.167,0.177 10 false *a 2.656,1.969 2.823,2.146 0.167,0.177 10 false *b
*a Timing Notch
*b Timing Mark "0"


Turn the crankshaft damper sub-assembly and align its timing notch with the timing mark "0" of the oil pump assembly.


j.
A116207C01
1.104,0.719 1.156,1.771 1.156,1.771 2.052,1.51 true 2.188,1.073 1.156,1.771 true 1.104,0.625 2.156,0.229 2.156,0.229 2.229,0.969 true 2.135,0.052 2.292,0.229 0.156,0.177 9 false *a 1.042,1.802 1.208,1.979 0.167,0.177 10 false *b
*a Paint Mark
*b Timing Mark


Check that all the pairs of timing marks are aligned.


k.

Clean and degrease the threads of the taper screw plug and threaded hole of the oil pump assembly.


l.
A201138C19
1.573,0.51 1.813,0.656 false 1.344,0.365 1.656,0.521 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to the 2 or 3 threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



m.

Using an 8 mm hexagon wrench, install the taper screw plug to the oil pump assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23820 7.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 17410 9.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 10.INSTALL FRONT FLOOR CENTER BRACE

Hide 12.INSPECT FOR ENGINE OIL LEAK

Hide 13.INSPECT FOR EXHAUST GAS LEAK

Hide 51441C 14.INSTALL ENGINE UNDER COVER RH