Home › Engine / Hybrid System › 1NZ-FE LUBRICATION › OIL PUMP › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017083 1NZ-FE LUBRICATION _0091241 OIL PUMP A

1NZ-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 15100C 1.INSTALL OIL PUMP SEAL

A166953E06
1.167,2.927 1.708,3.125 1.708,3.125 1.208,3.552 true 1.885,0.729 2.948,0.958 1.063,0.229 10 false 0 to -1.0 mm 1.76,3.052 2.063,3.208 0.302,0.156 10 false SST

a.

Using SST and a hammer, tap in a new oil pump seal until its surface is flush with the oil pump assembly.

SST
09950-60010  (09951-00250, 09952-06010)
09950-70010  (09951-07100, 09951-00410)

NOTICE:
·

Do not tap the oil seal at an angle.

·

Keep the seal lip free of foreign matter.



Oil seal tap in depth:

0 to -1.0 mm (0 to -0.0393 in.)



b.

Apply MP grease to the oil pump seal lip.


Hide 2.INSTALL TAPER SCREW PLUG

a.

Clean and degrease the threads of the taper screw plug and threaded hole of the oil pump assembly.


b.
A201138C19
1.573,0.51 1.813,0.656 false 1.344,0.365 1.656,0.521 0.313,0.156 10 false *a
*a Adhesive 1324


Apply adhesive to the 2 or 3 threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Using an 8 mm hexagon wrench, install the taper screw plug to the oil pump assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 15100 3.INSTALL OIL PUMP ASSEMBLY

a.

Install 2 new O-rings to the cylinder block sub-assembly and oil pan sub-assembly.


b.

Clean the contact surfaces of the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.


c.

Apply seal packing to the oil pump assembly, cylinder head sub-assembly and cylinder block sub-assembly as shown in the illustration.

A310576C01
1.26,6.396 1.656,6.021 false 1.135,6.385 0.865,6.031 false 3.417,6.927 3.177,7.292 3.177,7.292 2.948,6.927 false 2.406,4.875 2.677,5.208 2.677,5.208 2.208,4.885 false 2,4.51 2.458,3.833 true 1.198,2.24 0.76,2.396 true 1.573,0.573 1.323,0.333 true 2.063,0.969 2.573,0.25 2.573,0.25 2.24,1.719 true 4.781,1.24 4.385,0.365 4.385,0.365 5.792,1.281 true 1.146,0.208 1.458,0.365 0.313,0.156 10 false *a 0.604,2.292 0.917,2.448 0.313,0.156 10 false *b 4.208,0.25 4.521,0.406 0.313,0.156 10 false *c 3.104,7.281 3.417,7.438 0.313,0.156 10 false *e 5.208,2.167 5.521,2.323 0.313,0.156 10 false *f 1.427,9.01 1.719,9.281 0.292,0.271 10 false *g 2.385,8.844 2.698,9 0.313,0.156 10 false *h 2.604,0.156 2.917,0.313 0.313,0.156 10 false *a 1.531,1.469 1.688,1.667 0.156,0.198 10 false A 1.698,1.75 1.854,1.948 0.156,0.198 10 false A 2.719,0.698 2.875,0.896 0.156,0.198 10 false B 3.083,0.917 3.24,1.115 0.156,0.198 10 false B 1.344,2.531 1.479,2.719 0.135,0.188 10 false C 1.49,2.26 1.625,2.448 0.135,0.188 10 true C 4.5,0.927 4.635,1.115 0.135,0.188 10 false D 4.938,0.938 5.073,1.125 0.135,0.188 10 false D 1.885,3.542 2.198,3.75 0.313,0.208 10 false A-A 2.823,5.667 3.719,5.865 0.896,0.198 10 false B-B, C-C (*d) 0.938,5.677 1.563,5.885 0.625,0.208 10 false B-B, C-C 1.813,8.052 2.125,8.26 0.313,0.208 10 false D-D 4.563,4.385 4.875,4.542 0.313,0.156 10 false *a 4.573,7.052 4.885,7.208 0.313,0.156 10 false *b 4.615,8.323 4.927,8.479 0.313,0.156 10 false *b 4.594,5.365 4.823,5.583 0.229,0.219 10 false *a 0.344,3.844 1.354,4.031 1.01,0.188 10 false φ1.5 to 2.0 mm 5.438,5.479 6.448,5.667 1.01,0.188 10 false φ1.5 to 2.0 mm 0.313,4.031 1.594,4.219 1.281,0.188 10 false (φ0.059 to 0.079 in.) 5.406,5.635 6.688,5.823 1.281,0.188 10 false (φ0.059 to 0.079 in.) 5.417,8.396 6.427,8.583 1.01,0.188 10 false φ1.5 to 2.0 mm 5.375,8.563 6.656,8.75 1.281,0.188 10 false (φ0.059 to 0.079 in.) 2.521,3.719 3.198,3.896 0.677,0.177 10 false 2.5 mm 2.469,3.865 3.146,4.042 0.677,0.177 10 false (0.098 in.) 2.729,5.115 3.406,5.292 0.677,0.177 10 false 1.5 mm 2.698,5.26 3.375,5.438 0.677,0.177 10 false (0.059 in.) 1.625,4.948 2.302,5.125 0.677,0.177 10 false 5.0 mm 1.573,5.083 2.25,5.26 0.677,0.177 10 false (0.197 in.) 5.438,4.458 6.448,4.646 1.01,0.188 10 false φ3.5 to 4.5 mm 5.396,4.635 6.698,4.823 1.302,0.188 10 false (φ0.138 to 0.177 in.) 5.417,7.156 6.427,7.344 1.01,0.188 10 false φ3.5 to 4.5 mm 5.385,7.323 6.688,7.51 1.302,0.188 10 false (φ0.138 to 0.177 in.) 1.74,6.406 2.75,6.594 1.01,0.188 10 false φ3.5 to 4.5 mm 1.604,6.583 2.906,6.771 1.302,0.188 10 false (φ0.138 to 0.177 in.) 0.135,6.75 0.813,6.927 0.677,0.177 10 false 1.0 mm 0.104,6.906 0.781,7.083 0.677,0.177 10 false (0.039 in.) 0.26,5.917 0.938,6.094 0.677,0.177 10 false 2.5 mm 0.219,6.073 0.896,6.25 0.677,0.177 10 false (0.098 in.) 1.698,5.917 2.375,6.094 0.677,0.177 10 false 1.0 mm 1.677,6.073 2.354,6.25 0.677,0.177 10 false (0.039 in.)
*a Seal Packing (Other part) *b Seal Packing (Water Pump part)
*c Apply enough seal packing so that it will spread to the inner side *d After assembly
*e 2.5 mm (0.098 in.) or more *f Seal Packing application width 10 mm or more
*g φ10.0 mm (φ0.394 in.) or more *h Apply enough seal packing so that it will protrude beyond the Oil Pump Assembly installation surface


Seal packing:

Water pump part: Toyota Genuine Seal Packing 1282B: Three Bond 1282B or equivalent

Other part: Toyota Genuine Seal Packing Black: Three Bond 1207B or equivalent


NOTICE:
·

Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying seal packing.

·

Do not expose the seal to engine oil for at least 2 hours after the installation.




d.
A116558

Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.


e.

Temporarily install the oil pump assembly and 2 wire harness clamp brackets with the 16 bolts and nut.

A294817C02
2.031,2.479 1.823,2.219 false 2.458,2.49 2.146,1.99 false 1.313,0.479 1.51,0.271 true 1.563,0.219 1.875,0.375 0.313,0.156 10 false *1 1.979,2.51 2.292,2.667 0.313,0.156 10 false *2 2.406,2.51 2.719,2.667 0.313,0.156 10 false *2 1.615,0.615 1.771,0.813 0.156,0.198 10 false A 0.917,1.031 1.073,1.229 0.156,0.198 10 false B 0.927,1.25 1.083,1.448 0.156,0.198 10 false C 0.906,0.458 1.063,0.656 0.156,0.198 10 false E 1.031,0.844 1.188,1.042 0.156,0.198 10 false A 1.771,0.833 1.927,1.031 0.156,0.198 10 false C 0.969,1.5 1.125,1.698 0.156,0.198 10 false C 0.958,1.729 1.115,1.927 0.156,0.198 10 false C 1.052,2.125 1.208,2.323 0.156,0.198 10 false C 1.49,2.448 1.646,2.646 0.156,0.198 10 false C 1.76,2.51 1.917,2.708 0.156,0.198 10 false C 2.208,2.333 2.365,2.531 0.156,0.198 10 false C 2.406,2.125 2.563,2.323 0.156,0.198 10 false C 2.573,1.906 2.729,2.104 0.156,0.198 10 false B 2.552,1 2.708,1.198 0.156,0.198 10 false A 1.969,0.542 2.125,0.74 0.156,0.198 10 false A 6,1 6.156,1.198 0.156,0.198 10 false 1 4.49,0.844 4.646,1.042 0.156,0.198 10 false 2 5.438,0.531 5.594,0.729 0.156,0.198 10 false 3 5.063,0.625 5.219,0.823 0.156,0.198 10 false 4 4.385,1.031 4.542,1.229 0.156,0.198 10 false 5 4.396,1.24 4.552,1.438 0.156,0.198 10 false 6 4.448,1.49 4.604,1.688 0.156,0.198 10 false 7 4.438,1.729 4.594,1.927 0.156,0.198 10 false 8 4.531,2.125 4.688,2.323 0.156,0.198 10 false 9 4.927,2.438 5.177,2.635 0.25,0.198 10 false 10 5.198,2.51 5.448,2.708 0.25,0.198 10 false 11 5.615,2.365 5.865,2.563 0.25,0.198 10 false 12 5.823,2.177 6.073,2.375 0.25,0.198 10 false 13 6.01,1.917 6.26,2.115 0.25,0.198 10 false 14 5.198,0.833 5.448,1.031 0.25,0.198 10 false 15 4.292,0.448 4.542,0.646 0.25,0.198 10 false 16 6.031,0.719 6.281,0.917 0.25,0.198 10 false 17 2.583,0.708 2.74,0.906 0.156,0.198 10 false D
*1 Nut *2 Wire Harness Clamp Bracket


NOTICE:

Do not apply oil to the bolt A.


Bolt Length:
Item Length
Bolt A 30 mm (1.181 in.)
Bolt B 35 mm (1.378 in.)
Bolt C 20 mm (0.787 in.)
Bolt D (Double ended bolt) 20 mm (0.787 in.)



f.

Tighten the bolts and nut in the sequence shown in the illustration.

Torque:
Bolt A : 24 N*m (245 kgf*cm, 18 ft.*lbf)
Bolt B, C : 11 N*m (112 kgf*cm, 8 ft.*lbf)
Bolt D : 24 N*m (245 kgf*cm, 18 ft.*lbf)
Nut E : 24 N*m (245 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Be careful not to disturb the seal packing.

·

After installing the oil pump assembly, install the engine mounting bracket RH and engine water pump assembly within 15 minutes.




Hide 12315A 4.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH to the oil pump assembly with the 4 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 16100 5.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 16173 6.INSTALL WATER PUMP PULLEY

Hide 11101J 7.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 15100Q 8.INSTALL CRANKSHAFT POSITION SENSOR

Hide 13407 9.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

a.

Align the pin hole of the crankshaft damper sub-assembly with the pin of the crankshaft and install the crankshaft damper sub-assembly.


b.

Temporarily tighten the bolt to the crankshaft damper sub-assembly.


c.
A179643C01
1.854,1.594 2.625,0.427 2.625,0.427 2.063,1.865 true 0.646,1.167 0.719,1.563 0.719,1.563 0.396,1.385 false 1.167,3.146 1.479,3.302 0.313,0.156 10 false *a 2.677,3.219 2.896,3.396 0.219,0.177 10 false *b 2.688,0.354 3.094,0.594 0.406,0.24 10 false SST 0.781,1.51 1.177,1.74 0.396,0.229 10 false SST
*a Hold
*b Turn


Using SST, tighten the bolt of the crankshaft damper sub-assembly.

SST
09213-14010  (91651-60865)
09330-00021  (09330-00030)

Torque:
128 N*m (1305 kgf*cm, 94 ft.*lbf)

NOTICE:

Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



Hide 12305 10.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

a.
A106618C01
1.958,1.385 2.313,1.052 true 1.927,1.979 1.875,1.729 true 0.26,0.771 0.615,0.958 0.354,0.188 10 true A (1) 0.667,1.948 1,2.135 0.333,0.188 10 true A (2) 2.042,0.021 2.375,0.208 0.333,0.188 10 true A (3) 2.448,1.271 2.583,1.469 0.135,0.198 10 true B 2.344,0.927 2.5,1.104 0.156,0.177 10 true *1 1.875,1.99 2.031,2.167 0.156,0.177 10 true *1
*1 Nut


Temporarily install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH and vehicle with the 4 bolts and 2 nuts.


b.

Tighten the 3 bolts A in the order shown in the illustration.

Torque:
Bolt A : 52 N*m (530 kgf*cm, 38 ft.*lbf)


c.

Tighten the bolt B and 2 nuts.

Torque:
Bolt B, Nut : 52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 11201 11.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23820 12.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 12261 13.CONNECT VENTILATION HOSE

Hide 27060 15.INSTALL GENERATOR WITH REGULATOR ASSEMBLY

Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 17.INSTALL FRONT FLOOR CENTER BRACE

Hide 58910C 18.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 19.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 26.INSPECT FOR EXHAUST GAS LEAK

Hide 51441C 27.INSTALL ENGINE UNDER COVER RH

Hide 28.INSTALL FRONT WHEEL RH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)