83181G
1.INSTALL SPEEDOMETER SENSOR (w/o ABS)
33403K
2.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)
Apply a light coat of gear oil to a new O-ring and install it to the speedometer driven hole cover sub-assembly.
Do not twist the O-ring.
Install the speedometer driven hole cover sub-assembly to the manual transaxle assembly with the bolt.
Make sure that the O-ring is not damaged or does not jump out of position during installation.
3.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 3 wire harness clamp brackets to the manual transaxle assembly with the 3 bolts.
30300
4.INSTALL MANUAL TRANSAXLE ASSEMBLY
|
Clutch Spline Grease |
Apply clutch spline grease to the input shaft spline.
Toyota Genuine Clutch Spline Grease or equivalent
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
Align the input shaft with the clutch disc assembly and install the manual transaxle assembly to the engine assembly.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not forcibly pry on the manual transaxle assembly.
When mounting the manual transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.
When tightening the bolts, be sure that the contact surfaces of the engine assembly and manual transaxle assembly are in close contact with one another.
Install the 4 bolts from the manual transaxle assembly side.
| Item | Length |
|---|---|
| Bolt A | 45 mm (1.77 in.) |
| Bolt B | 80 mm (3.15 in.) |
| *a | Adhesive |
Clean and degrease the engine mounting bracket LH installation bolts and bolt holes.
Apply adhesive to 2 or 3 threads on the ends of the 5 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
| *a | Temporarily Tighten |
Install the engine mounting bracket LH to the manual transaxle assembly with the 5 bolts in the order shown in the illustration.
| *a | Temporarily Tighten |
Engage the hook to temporarily install the engine mounting insulator LH to the body.
Install the 5 bolts in the order shown in the illustration.
Install the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.
Turn the bolt while holding the nut.
Install the 4 bolts from the engine assembly side.
12313
5.INSTALL ENGINE MOVING CONTROL ROD BRACKET
| *a | Temporarily Tighten |
Install the engine moving control rod bracket to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.
51201
6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
28100
7.INSTALL STARTER ASSEMBLY
8.INSTALL FRONT DRIVE SHAFT ASSEMBLIES
43498A
9.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR
17410
10.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Sedan)
17410
11.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Hatchback)
57533B
12.INSTALL FRONT FLOOR CENTER BRACE (for Sedan)
57533B
13.INSTALL FRONT FLOOR CENTER BRACE (for Hatchback)
31470
14.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
Install the clutch release cylinder assembly to the manual transaxle assembly with the 2 bolts B.
Install the clutch release cylinder to flexible hose tube to the manual transaxle assembly with the 2 bolts A.
Install a new clip.
82121
15.CONNECT ENGINE WIRE
Install the wire harness clamp bracket to the manual transaxle assembly with the bolt B.
Engage the 7 clamps and install the engine wire to the wire harness clamp brackets.
Install the engine wire to the manual transaxle assembly with the bolt A.
Connect the connector to the oxygen sensor.
Connect the connector to the back-up light switch assembly.
w/o ABS:
Connect the connector to the speedometer sensor.
33820B
16.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
| *a | Paint Mark |
Install the transmission control cable assembly to the floor shift control lever housing support bracket with 2 new clips B.
Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the floor shift control lever housing support bracket before installing the clips.
Connect the transmission control cable assembly to the manual transaxle assembly with the 2 washers and 2 clips A.
74410
17.INSTALL BATTERY CARRIER ASSEMBLY
74431
18.INSTALL BATTERY TRAY
19.INSTALL BATTERY
17701
20.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
21.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
22.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
17880
23.INSTALL AIR CLEANER HOSE ASSEMBLY
12262
24.CONNECT NO. 2 VENTILATION HOSE
25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
26.ADD MANUAL TRANSAXLE OIL
27.INSPECT MANUAL TRANSAXLE OIL
28.INSPECT FOR MANUAL TRANSAXLE OIL LEAK
29.INSPECT FOR EXHAUST GAS LEAK
Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION