Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › 2016.07–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0259988 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35141D 1.INSTALL BREATHER PLUG HOSE

HINT:

Perform this procedure only when replacement of the breather plug hose is necessary.


a.

Apply Toyota Genuine CVT fluid FE to a new O-ring, and install it to the No. 2 breather plug (CVT).

NOTICE:

Be careful not to damage or twist the O-ring.



b.

Install the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) to the breather plug hose.


c.

Install the breather plug hose to the continuously variable transaxle assembly.


Hide 2.INSTALL STRAIGHT SCREW PLUG

a.

Install the straight screw plug and a new gasket to the continuously variable transaxle assembly.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 35123B 3.INSTALL TRANSMISSION BREATHER SKIRT

a.

Install the transmission breather skirt to the continuously variable transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Install the clamp to the transmission breather skirt.


c.

Install the No. 1 breather plug (CVT) to the clamp.


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C349379N01
0.635,3.333 0.854,3.531 0.219,0.198 10 true A 1.594,2.49 1.813,2.688 0.219,0.198 10 true B 2.104,0.771 2.229,0.969 0.125,0.198 10 true B 2.917,1.156 3.083,1.354 0.167,0.198 10 true B 0.656,0.167 0.781,0.365 0.125,0.198 10 true B

Install the 5 wire harness clamp brackets to the continuously variable transaxle assembly with the 5 bolts.

Torque:
Bolt (A) : 39 N*m (398 kgf*cm, 29 ft.*lbf)
Bolt (B) : 12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 30400E 5.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


b.

Temporarily install the CVT oil pump type T oil seal by pressing it to the installation surface of the oil pump housing by hand.

NOTICE:

Be sure to install the CVT oil pump type T oil seal in the correct direction.



c.

Clean the CVT oil pump type T oil seal contact surface of SST and the area around it.

SST
09309-36010  


d.
C329653C01
1.677,2.49 1.677,2.115 false 0.833,2.771 1.146,2.927 0.313,0.156 10 false *a 1.573,2.521 2.031,2.719 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.

Standard Depth:

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:
·

Drive the CVT oil pump type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the oil pump housing.

·

Wipe any extra grease off with your hand.




Hide 32000A 6.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C349370C01
2.25,0.188 1.958,0.49 true 1,0.313 0.802,0.635 true 0.792,1.125 0.958,1.396 true 1.146,1.115 1.042,0.875 true 0.396,1.271 0.531,0.885 true 2.281,0.073 2.469,0.25 0.188,0.177 10 true *a 0.885,1.396 1.104,1.594 0.219,0.198 10 true *b 1.01,0.208 1.198,0.385 0.188,0.177 10 true *b 1.135,1.083 1.292,1.281 0.156,0.198 10 true *c 0.313,1.26 0.51,1.49 0.198,0.229 10 true *c
*a Matchmark
*b Wide Groove
*c Narrow Groove


Turn the front oil pump drive gear so that the groove is at the top and place a matchmark on the transaxle housing to indicate the position of the groove.

NOTICE:
·

Place the matchmark on the transaxle housing to indicate the position of the wide groove.

·

The matchmark position must be correct to prevent damage.




b.
C267518C03
1.448,1.813 1.698,1.625 true 1.698,0.281 2.01,0.125 false 2.042,0.042 2.24,0.208 0.198,0.167 10 false *a 1.271,1.76 1.479,1.948 0.208,0.188 10 false *b
*a Key
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.


c.
C349371C01
1.125,0.792 1.583,0.229 1.583,0.229 1.115,0.594 true 2.438,1.292 2.188,0.708 2.188,0.708 2.448,0.917 true 1.615,0.156 1.885,0.385 0.271,0.229 10 true *a 2.031,0.625 2.302,0.854 0.271,0.229 10 false *1
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




d.
C349372C01
2.458,1.219 2.219,0.552 2.219,0.552 2.5,0.854 true 1.146,0.573 1.438,0.25 true 1.135,1.531 1.417,2 true 2.073,0.49 2.385,0.688 0.313,0.198 10 false *1 1.469,0.146 1.781,0.344 0.313,0.198 10 false *a 1.448,1.917 1.76,2.115 0.313,0.198 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




e.
C349373C01
2.469,1.271 2.198,0.531 2.198,0.531 2.521,0.865 true 1.115,0.74 1.417,0.281 1.417,0.281 1.115,0.552 true 2.052,0.479 2.365,0.635 0.313,0.156 10 false *1 1.448,0.188 1.76,0.344 0.313,0.156 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the key of the torque converter assembly into the groove of the front oil pump drive gear.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT oil pump type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C354267C01
2.5,0.885 2.635,0.635 false 2.573,1.26 2.708,1.01 false 0.688,2.052 0.958,1.823 true 1.885,1.99 1.521,1.688 true 2.448,0.25 2.604,0.448 0.156,0.198 10 false A 2.406,0.896 2.563,1.094 0.156,0.198 10 false *a 2.49,1.271 2.646,1.469 0.156,0.198 10 false *b 0.542,1.979 0.698,2.177 0.156,0.198 10 true *a 1.927,1.958 2.083,2.156 0.156,0.198 10 false *b
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C354268N01
2.49,0.208 2.948,0.406 0.458,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30400 7.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.

Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 30400 8.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C304848C01
1.635,0.875 2.5,0.25 true 0.833,0.25 1.167,0.521 false 0.667,0.177 0.979,0.375 0.313,0.198 10 false *1 2.552,0.177 2.865,0.375 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



b.
C354269C01
1.5,0.667 2.906,0.313 2.906,0.313 2.708,0.76 true 2.938,0.24 3.25,0.438 0.313,0.198 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.
C349368N01
1.49,0.083 1.646,0.281 0.156,0.198 10 false A 2.271,0.188 2.427,0.385 0.156,0.198 10 false A 2.573,0.792 2.729,0.99 0.156,0.198 10 false A 2.594,1.323 2.75,1.521 0.156,0.198 10 false A 2.354,1.688 2.51,1.885 0.156,0.198 10 true B 2.073,1.875 2.229,2.073 0.156,0.198 10 true B 1.625,1.938 1.781,2.135 0.156,0.198 10 true B 1.208,1.76 1.365,1.958 0.156,0.198 10 true B

Install the continuously variable transaxle assembly to the engine assembly with the 8 bolts.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A): Install from continuously variable transaxle assembly side

·

Bolt (B): Install from engine assembly side




Hide 12325A 9.INSTALL ENGINE MOUNTING BRACKET LH

a.

Clean and degrease the bolts and the installation holes in the engine mounting bracket LH.


b.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
C354277C01
0.417,1.406 0.969,1.583 0.552,0.177 10 true 1 (*a), 4 2.052,1.76 2.229,1.917 0.177,0.156 10 true 3 1.458,0.979 1.635,1.135 0.177,0.156 10 true 2
*a Temporarily Tighten


Install the engine mounting bracket LH to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12372A 10.INSTALL ENGINE MOUNTING INSULATOR LH

a.
C354276C01
1.917,0.677 2.51,0.885 0.594,0.208 10 true 2 (*a), 7 1.271,0.375 1.865,0.583 0.594,0.208 10 true 1 (*a), 6 0.896,1.135 1.021,1.354 0.125,0.219 10 true 4 1.635,1.896 1.75,2.104 0.115,0.208 10 true 3 2.396,1.125 2.583,1.302 0.188,0.177 10 true 5
*a Temporarily Tighten


Engage the hook to temporarily install the engine mounting insulator LH to the vehicle body with the 5 bolts.


b.

Fully tighten the 5 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


c.
C354275

Install the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

NOTICE:

Turn the bolt while holding the nut.



Hide 32101G 11.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


b.
C321585C03
1.865,1.688 1.865,1.427 false 1.813,1.719 2.125,1.875 0.313,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
C349377N01
2.083,1.615 1.865,1.333 true 2.146,1.542 2.479,1.708 0.333,0.167 10 true SST

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley with SST.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11363A 12.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 13.INSTALL STARTER ASSEMBLY

Hide 12364A 14.INSTALL ENGINE LATERAL CONTROL ROD

a.
C354280C01
2.365,0.688 2.927,0.875 0.563,0.188 10 true 1 (*a), 5 2.073,1.281 2.26,1.479 0.188,0.198 10 true 4 1.698,1.365 1.885,1.563 0.188,0.198 10 true 2 1.333,1.156 1.521,1.354 0.188,0.198 10 true 3
*a Temporarily Tighten


Install the engine lateral control rod to the continuously variable transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 51201 15.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 43498A 17.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR

Hide 17410 18.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Sedan)

Hide 17410 19.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Hatchback)

Hide 57533B 20.INSTALL FRONT FLOOR CENTER BRACE (for Sedan)

Hide 57533B 21.INSTALL FRONT FLOOR CENTER BRACE (for Hatchback)

Hide 45025D 22.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 23.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45209 24.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 25.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33823 26.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 16260 27.CONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C354297C01
1.5,3 1.365,2.708 false 0.969,1.573 1.125,1.771 0.156,0.198 10 false A 1.583,1.885 1.74,2.083 0.156,0.198 10 false A 0.542,2.125 0.698,2.323 0.156,0.198 10 false *a 1.542,2.594 1.698,2.792 0.156,0.198 10 false *c 1.052,3.104 1.208,3.302 0.156,0.198 10 false *b 1.49,3.01 1.646,3.208 0.156,0.198 10 false *d
*a View A
*b Front of Vehicle
*c Left of Vehicle
*d Paint Mark


Engage the 2 clamps to install the water by-pass hose assembly to the continuously variable transaxle assembly.


b.

Connect the 2 water by-pass hoses to the transmission oil cooler and slide the 2 hose clips to secure them as shown in the illustration.

NOTICE:
·

Fully insert the 2 water by-pass hoses until the 2nd rib on each transmission oil cooler pipe.

·

Perform the installation with the hose clips at the correct directions.




Hide 82121 28.CONNECT ENGINE WIRE

a.
C349375C01
1.5,3.458 1.813,3.656 0.313,0.198 10 true *1 1.385,4.135 1.604,4.365 0.219,0.229 10 true *2
*1 Transmission Revolution Sensor (NOUT) Connector
*2 Oil Pressure Sensor Connector


Engage the 4 clamps to connect the engine wire to the continuously variable transaxle assembly.


b.

Connect the oil pressure sensor connector.


c.

Connect the transmission revolution sensor (NOUT) connector.


d.
C349374C01
0.844,3.969 1.042,4.167 0.198,0.198 10 true *1 1.25,3.385 1.427,3.604 0.177,0.219 10 true *2 2.583,3.438 2.802,3.604 0.219,0.167 10 true *3 2.615,1.292 2.802,1.469 0.188,0.177 10 true *4
*1 Heated Oxygen Sensor Connector
*2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector
*4 Park/Neutral Position Switch Assembly Connector


Engage the 4 clamps to connect the engine wire to the continuously variable transaxle assembly.


e.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


f.

Connect the park/neutral position switch assembly connector.


g.

Connect the transmission revolution sensor (NIN) connector.


h.

Connect the transmission wire connector.


i.

Connect the heated oxygen sensor connector.


Hide 33820B 29.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58910C 30.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 31.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 17701 35.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 36.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17880 38.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 39.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 40.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 42.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 44.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 45.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Hide 46.INSPECT SHIFT LEVER POSITION

Hide 47.ADJUST SHIFT LEVER POSITION

Hide 51441C 48.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 49.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 50.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 51.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 53.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT