Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _51 Engine / Hybrid System _052909 CRUISE CONTROL _0256264 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

C388523E01
6.49,4.271 7.104,4.469 0.615,0.198 10 false F130 6.49,4.438 7.104,4.635 0.615,0.198 10 false ECM 4.823,4.115 5.438,4.313 0.615,0.198 10 false F143 5.24,4.115 5.563,4.323 0.323,0.208 10 false F8 5.24,3.208 5.563,3.417 0.323,0.208 10 false F8 4.823,3.208 5.438,3.406 0.615,0.198 10 false F143 3.479,3.208 3.813,3.427 0.333,0.219 10 false z7 3.469,4.104 3.802,4.323 0.333,0.219 10 false z7 3.5,3.906 3.833,4.125 0.333,0.219 10 false 4 3.5,2.99 3.833,3.208 0.333,0.219 10 false 3 2.708,3.083 3.042,3.302 0.333,0.219 10 false 3 2.698,3.979 3.031,4.198 0.333,0.219 10 false 1 0.531,3.604 0.865,3.948 0.333,0.344 10 false CAN CEL 1.063,3.677 1.531,3.885 0.469,0.208 10 false -/SET 2.313,3.594 2.646,3.979 0.333,0.385 10 false ON- OFF 1.688,3.667 2.156,3.875 0.469,0.208 10 false +/RES 0.542,4.5 2.271,4.719 1.729,0.219 10 false Cruise Control Main Switch 2.75,4.625 3.667,5.042 0.917,0.417 10 false Cruise Control Switch Wire 3.823,4.5 4.74,4.917 0.917,0.417 10 false Spiral Cable Sub-assembly 4.427,3.99 5.042,4.188 0.615,0.198 10 false ECC 4.427,3.094 5.042,3.292 0.615,0.198 10 false CCS 4.938,3 5.271,3.219 0.333,0.219 10 false 1 5.271,3 5.604,3.219 0.333,0.219 10 false 1 4.927,3.906 5.26,4.125 0.333,0.219 10 false 2 5.271,3.906 5.604,4.125 0.333,0.219 10 false 2 6.083,1.313 6.417,1.531 0.333,0.219 10 false 21 6.083,0.615 6.417,0.833 0.333,0.219 10 false 22 6.375,0.74 6.99,0.938 0.615,0.198 10 false CCS 6.385,1.438 7,1.635 0.615,0.198 10 false ECCS 4.917,4.323 5.24,4.531 0.323,0.208 10 false *1 5.26,4.323 5.583,4.531 0.323,0.208 10 false *2 4.906,3.417 5.229,3.625 0.323,0.208 10 false *1 5.25,3.417 5.573,3.625 0.323,0.208 10 false *2 0.229,5.073 1.958,5.292 1.729,0.219 10 false *1: for TMT Made 0.219,5.406 1.948,5.625 1.729,0.219 10 false *2: for TMMIN Made

PROCEDURE

1.READ VALUE ON GTS
a.
E107091C01
2.144,0.084 2.42,0.273 0.276,0.189 10 *c 2.763,1.172 3.003,1.374 0.24,0.202 10 *a 1.934,1.577 2.325,1.779 0.391,0.202 10 *b 1.033,1.235 1.268,1.437 0.235,0.202 10 *d
*a ON-OFF
*b -/SET
*c +/RES
*d CANCEL


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control main switch.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) released
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 237 16,23,22,21
OK:

When the cruise control main switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
E232246C06
0.24,1.344 0.667,1.646 0.427,0.302 0.333,0.854 0.5,1.031 0.167,0.177 10 false *a 0.333,3.177 0.5,3.354 0.167,0.177 10 false *b 0.396,1.406 0.833,1.76 0.438,0.354 10 false z7
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
Cruise control main switch side connector terminal 3 - z7-3 Below 1 Ω
Cruise control main switch side connector terminal 1 - z7-4 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the F130 ECM connector.


b.

Disconnect the F143*1 or F8*2 spiral cable sub-assembly connector.

·

*1: for TMT Made

·

*2: for TMMIN Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):

for TMT Made

Tester Connection Condition Specified Condition
F130-22 (CCS) - F143-1 (CCS) Always Below 1 Ω
F130-21 (ECCS) - F143-2 (ECC) Always Below 1 Ω

for TMMIN Made

Tester Connection Condition Specified Condition
F130-22 (CCS) - F8-1 (CCS) Always Below 1 Ω
F130-21 (ECCS) - F8-2 (ECC) Always Below 1 Ω


Standard Resistance (Check for Short):

for TMT Made

Tester Connection Condition Specified Condition
F130-22 (CCS) or F143-1 (CCS) - Body ground Always 10 kΩ or higher
F130-21 (ECCS) or F143-2 (ECC) - Body ground Always 10 kΩ or higher

for TMMIN Made

Tester Connection Condition Specified Condition
F130-22 (CCS) or F8-1 (CCS) - Body ground Always 10 kΩ or higher
F130-21 (ECCS) or F8-2 (ECC) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)