Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE(for TMT Made) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0334259 SPIRAL CABLE(for TMT Made) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE(for TMT Made)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 55661A 5.REMOVE INSTRUMENT PANEL REGISTER BEZEL

Hide 55411G 6.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL

Hide 45289A 7.REMOVE STEERING COLUMN COVER SUPPORT (w/ Smart Entry and Start System)

Hide 45287 8.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 9.REMOVE UPPER STEERING COLUMN COVER

Hide 84307 10.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ VSC)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.
B487771C01
0.594,3.021 0.875,2.583 true 0.375,2.938 0.698,3.188 0.323,0.25 10 false *1
*1 Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connectors from the spiral cable with sensor sub-assembly.


f.
B484568

Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.


Hide 84306 11.REMOVE SPIRAL CABLE SUB-ASSEMBLY (w/ VSC)

NOTICE:
·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly or the steering sensor.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in the center position of the steering sensor becoming misaligned. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly when removing the steering sensor from the spiral cable sub-assembly.



a.

When replacing the steering sensor:

i.
C381050

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.




ii.
C381049C03
2.354,1.229 1.885,0.948 1.885,0.948 2.333,0.729 true 2.802,0.906 3.167,0.521 true 0.281,0.542 0.615,0.896 true 1.688,0.865 2,1.021 0.313,0.156 10 false *a 3.198,0.396 3.427,0.604 0.229,0.208 10 false *b 0.104,0.438 0.333,0.646 0.229,0.208 10 false *b
*a Guide
*b Pin


Disengage the 6 claws, 2 guides and 2 pins to remove the spiral cable sub-assembly from the steering sensor.

NOTICE:

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.




Hide 12.REMOVE SPIRAL CABLE SUB-ASSEMBLY (w/o VSC)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.
B487772C01
0.542,3.021 0.75,2.646 true 0.344,2.948 0.656,3.146 0.313,0.198 10 false *1
*1 Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.
B495586

Disengage the 3 claws to remove the spiral cable sub-assembly.