Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086991 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

When the heater control and accessory assembly is operated, the heater relay will turn on to allow current to flow to the blower motor and then the motor will start rotating. Operating the heater control and accessory assembly switches the current flow between the blower resistor and body ground, thus, shifting the rotation speed of the blower motor with fan sub-assembly.

WIRING DIAGRAM

for TMMIN Made


E152023E02
0.083,0.083 6.135,0.323 6.052,0.24 12 false Through No. 9 Junction Connector: 0.146,0.719 1.542,1.594 1.396,0.875 10 false from Ignition or Starter Switch Assembly 1.938,0.875 3.771,1.073 1.833,0.198 10 false ECU-IG NO. 1 3.667,0.615 4.031,0.865 0.365,0.25 10 false 1 2.885,0.615 3.25,0.865 0.365,0.25 10 false 2 2.896,1.156 3.26,1.406 0.365,0.25 10 false 5 3.656,1.156 4.021,1.406 0.365,0.25 10 false 3 5.594,0.615 5.958,0.865 0.365,0.25 10 false 20 5.844,0.719 6.208,0.969 0.365,0.25 10 false HR 5.594,1.146 5.958,1.396 0.365,0.25 10 false 26 5.844,1.26 6.438,1.5 0.594,0.24 10 false SBLW 5.604,1.573 6.198,1.813 0.594,0.24 10 false F124 5.594,1.74 7.156,2.219 1.563,0.479 10 false Air Conditioning Amplifier Assembly 2.927,1.573 3.521,1.813 0.594,0.24 10 false F78 2.917,1.719 4.052,2.01 1.135,0.292 10 false Heater Relay 2.448,1.427 3.042,1.667 0.594,0.24 10 false HTR 0.74,1.958 1.875,2.25 1.135,0.292 10 false from Battery 2.479,2.396 3.073,2.635 0.594,0.24 10 false F53 2.469,2.552 3.875,3.063 1.406,0.51 10 false Blower Motor with Fan Sub-assembly 4.083,2.302 4.448,2.552 0.365,0.25 10 false 2 4.083,2.938 4.448,3.188 0.365,0.25 10 false 1 1.552,4.302 2.146,4.542 0.594,0.24 10 false 4 2.104,5.448 2.698,5.688 0.594,0.24 10 false 2 2.104,5.875 2.698,6.115 0.594,0.24 10 false 3 1.531,4.521 2.125,4.76 0.594,0.24 10 false HI 0.292,5.313 0.885,5.552 0.594,0.24 10 false F55 0.281,5.469 1.406,5.854 1.125,0.385 10 false Blower Resistor 1.802,5.427 2.396,5.667 0.594,0.24 10 false M2 1.813,5.885 2.406,6.125 0.594,0.24 10 false M1 1.563,6.458 2.156,6.698 0.594,0.24 10 false E 1.583,6.667 2.177,6.906 0.594,0.24 10 false 1 3.563,5.115 4.156,5.354 0.594,0.24 10 false 0 3.563,5.344 3.927,5.594 0.365,0.25 10 false 1 3.458,5.563 3.823,5.813 0.365,0.25 10 false 1 - 2 3.479,6 3.844,6.25 0.365,0.25 10 false 2 - 3 3.583,5.781 3.948,6.031 0.365,0.25 10 false 2 3.573,6.229 3.938,6.479 0.365,0.25 10 false 3 3.479,6.438 3.844,6.688 0.365,0.25 10 false 3 - 4 3.573,6.667 3.938,6.917 0.365,0.25 10 false 4 3.313,6.885 4.438,7.271 1.125,0.385 10 false Blower Switch 3.188,7.271 3.781,7.51 0.594,0.24 10 false F5 3.188,7.417 6.115,7.771 2.927,0.354 10 false Heater Control and Accessory Assembly 6.26,7.25 6.854,7.49 0.594,0.24 10 false 10 6.333,7.042 6.927,7.281 0.594,0.24 10 false E 6.406,4.906 7,5.146 0.594,0.24 10 false E 4.146,4.906 4.74,5.146 0.594,0.24 10 false HI 4.688,4.906 5.281,5.146 0.594,0.24 10 false M2 5.25,4.906 5.844,5.146 0.594,0.24 10 false M1 5.823,4.906 6.417,5.146 0.594,0.24 10 false LO 3.854,4.49 4.448,4.729 0.594,0.24 10 false HI 4.542,4.49 5.135,4.729 0.594,0.24 10 false M2 5.104,4.49 5.698,4.729 0.594,0.24 10 false M1 5.677,4.479 6.271,4.719 0.594,0.24 10 false LO 3.906,4.271 4.271,4.521 0.365,0.25 10 false 5 4.615,4.281 5.208,4.521 0.594,0.24 10 false 6 5.219,4.281 5.583,4.531 0.365,0.25 10 false 1 5.781,4.281 6.146,4.531 0.365,0.25 10 false 3

E152022E06
0.083,0.083 6.875,0.323 6.792,0.24 12 false Not Through No. 9 Junction Connector: 0.146,0.708 1.552,1.542 1.406,0.833 10 false from Ignition or Starter Switch Assembly 1.927,0.875 3.063,1.167 1.135,0.292 10 false ECU-IG NO. 1 2.875,0.615 3.208,0.844 0.333,0.229 10 false 2 3.646,0.615 3.979,0.844 0.333,0.229 10 false 1 2.885,1.177 3.219,1.365 0.333,0.188 10 false 5 3.646,1.156 3.979,1.344 0.333,0.188 10 false 3 5.594,0.625 5.927,0.854 0.333,0.229 10 false 20 5.854,0.719 6.188,0.948 0.333,0.229 10 false HR 5.604,1.156 5.938,1.385 0.333,0.229 10 false 26 5.833,1.25 6.688,1.49 0.854,0.24 10 false SBLW 5.594,1.573 6.448,1.813 0.854,0.24 10 false F124 5.583,1.729 7.135,2.24 1.552,0.51 10 false Air Conditioning Amplifier Assembly 2.448,1.406 3.302,1.646 0.854,0.24 10 false HTR 2.927,1.583 3.781,1.823 0.854,0.24 10 false F78 2.917,1.729 3.99,1.969 1.073,0.24 10 false Heater Relay 0.771,1.958 1.844,2.198 1.073,0.24 10 false from Battery 4.083,2.302 4.417,2.531 0.333,0.229 10 false 2 4.083,2.917 4.417,3.146 0.333,0.229 10 false 1 2.49,2.448 3.344,2.688 0.854,0.24 10 false F53 2.479,2.604 3.906,3.083 1.427,0.479 10 false Blower Motor with Fan Sub-assembly 1.563,4.313 1.969,4.521 0.406,0.208 10 false 4 1.521,4.521 1.927,4.729 0.406,0.208 10 false HI 3.844,4.49 4.25,4.698 0.406,0.208 10 false HI 4.146,4.896 4.552,5.104 0.406,0.208 10 false HI 0.313,5.292 0.719,5.5 0.406,0.208 10 false F55 0.302,5.438 1.667,5.74 1.365,0.302 10 false Blower Resistor 1.813,5.438 2.219,5.646 0.406,0.208 10 false M2 1.823,5.885 2.229,6.094 0.406,0.208 10 false M1 2.115,5.438 2.521,5.646 0.406,0.208 10 false 2 1.542,6.667 1.948,6.875 0.406,0.208 10 false 1 2.115,5.896 2.521,6.104 0.406,0.208 10 false 3 4.542,4.49 4.948,4.698 0.406,0.208 10 false M2 5.104,4.479 5.51,4.688 0.406,0.208 10 false M1 5.677,4.479 6.083,4.688 0.406,0.208 10 false LO 3.906,4.271 4.313,4.479 0.406,0.208 10 false 5 4.594,4.281 5,4.49 0.406,0.208 10 false 6 5.198,4.271 5.531,4.5 0.333,0.229 10 false 1 5.771,4.271 6.104,4.5 0.333,0.229 10 false 3 4.677,4.896 5.083,5.104 0.406,0.208 10 false M2 5.24,4.896 5.646,5.104 0.406,0.208 10 false M1 5.823,4.896 6.229,5.104 0.406,0.208 10 false LO 1.563,6.448 1.969,6.656 0.406,0.208 10 false E 6.417,4.896 6.823,5.104 0.406,0.208 10 false E 3.563,5.125 3.969,5.333 0.406,0.208 10 false 0 3.573,5.781 3.979,5.99 0.406,0.208 10 false 2 3.469,5.552 3.875,5.76 0.406,0.208 10 false 1 - 2 3.479,6 3.885,6.208 0.406,0.208 10 false 2 - 3 3.49,6.438 3.896,6.646 0.406,0.208 10 false 3 - 4 3.563,5.333 3.969,5.542 0.406,0.208 10 false 1 3.583,6.667 3.99,6.875 0.406,0.208 10 false 4 3.583,6.229 3.99,6.438 0.406,0.208 10 false 3 3.313,6.885 4.594,7.156 1.281,0.271 10 false Blower Switch 6.313,7.031 6.719,7.24 0.406,0.208 10 false E 3.229,7.25 3.635,7.458 0.406,0.208 10 false F5 3.229,7.396 6.104,7.719 2.875,0.323 10 false Heater Control and Accessory Assembly 6.24,7.26 6.646,7.469 0.406,0.208 10 false 10


for TMT Made


E376555E01
4.74,6.667 6.073,6.885 1.333,0.219 10 false Blower Switch 0.104,0.563 1.031,1.563 0.927,1 10 false from Ignition or Starter Switch Assembly*1 or IG1 Relay*2 1.385,0.906 3.219,1.104 1.833,0.198 10 false ECU-IG NO. 1 0.406,2.021 2.24,2.219 1.833,0.198 10 false from Battery 1.771,2.208 3.604,2.406 1.833,0.198 10 false HTR 2.781,2.385 4.615,2.583 1.833,0.198 10 false HTR 3.729,2.24 5.563,2.438 1.833,0.198 10 false F53 3.24,1.417 3.396,1.615 0.156,0.198 10 false 1 4.302,1.927 4.458,2.125 0.156,0.198 10 false 1 2.469,1.417 2.625,1.615 0.156,0.198 10 false 2 2.469,1.927 2.625,2.125 0.156,0.198 10 false 5 3.24,1.938 3.396,2.135 0.156,0.198 10 false 3 3.729,1.927 3.885,2.125 0.156,0.198 10 false 2 3.729,2.417 4.896,2.865 1.167,0.448 10 false Blower Motor with Fan Sub-assembly 5.594,2.448 6.781,2.792 1.188,0.344 10 false F124 5.594,2.635 7.156,3.26 1.563,0.625 10 false Air Conditioning Amplifier Assembly 6.031,1.542 7.156,1.792 1.125,0.25 10 false HR 6.031,2.042 7.156,2.292 1.125,0.25 10 false SBLW 5.792,1.438 6.125,1.708 0.333,0.271 10 false 20 5.792,1.927 6.125,2.198 0.333,0.271 10 false 26 3.885,7.188 5.073,7.531 1.188,0.344 10 false F5 3.885,7.344 6.802,7.635 2.917,0.292 10 false Heater Control and Accessory Assembly 0.635,6.75 1.823,7.094 1.188,0.344 10 false F55 0.635,6.917 1.823,7.26 1.188,0.344 10 false Blower Resistor 3.813,6.365 4.938,6.615 1.125,0.25 10 false E 5.146,4.365 6.271,4.615 1.125,0.25 10 false LO 4.719,4.365 5.844,4.615 1.125,0.25 10 false M1 4.292,4.365 5.417,4.615 1.125,0.25 10 false M2 3.948,4.375 5.073,4.625 1.125,0.25 10 false HI 4.115,4.615 5.24,4.865 1.125,0.25 10 false HI 4.458,4.604 5.583,4.854 1.125,0.25 10 false M2 4.854,4.615 5.979,4.865 1.125,0.25 10 false M1 5.24,4.604 6.365,4.854 1.125,0.25 10 false LO 5.656,4.615 6.781,4.865 1.125,0.25 10 false E 5.104,3.99 5.458,4.198 0.354,0.208 10 false 7*3 5.104,4.167 5.458,4.375 0.354,0.208 10 false 8*4 0.198,8.063 3.177,8.427 2.979,0.365 10 false *1: w/o Smart Entry & Start System 4.708,4.167 5.063,4.375 0.354,0.208 10 false 8*4 4.719,3.99 5.073,4.198 0.354,0.208 10 false 9*3 4.333,4.146 4.688,4.354 0.354,0.208 10 false 10 4.021,4.146 4.375,4.354 0.354,0.208 10 false 5 3.604,6.229 3.76,6.427 0.156,0.198 10 false 1 2.771,6.063 3.094,6.24 0.323,0.177 10 false 1*3 2.76,6.25 3.083,6.427 0.323,0.177 10 false 4*4 1.917,6.021 2.24,6.198 0.323,0.177 10 false 2*4 1.51,6.01 1.833,6.188 0.323,0.177 10 false 3*4 1.51,5.823 1.833,6 0.323,0.177 10 false 2*3 1.917,5.823 2.24,6 0.323,0.177 10 false 3*3 0.208,6.052 0.531,6.229 0.323,0.177 10 false 4*3 0.198,6.25 0.521,6.427 0.323,0.177 10 false 1*4 0.552,6.24 1.677,6.49 1.125,0.25 10 false HI 1.5,6.229 2.625,6.479 1.125,0.25 10 false M2 1.938,6.219 3.063,6.469 1.125,0.25 10 false M1 2.552,6.229 3.677,6.479 1.125,0.25 10 false E 0.177,8.438 3.156,8.802 2.979,0.365 10 false *2: w/ Smart Entry & Start System 2.677,8.063 5.656,8.427 2.979,0.365 10 false *3: for LHD 2.698,8.438 5.677,8.802 2.979,0.365 10 false *4: for RHD 6.083,4.823 6.354,5.042 0.271,0.219 10 false 0 6.083,5.042 6.354,5.26 0.271,0.219 10 false 1 5.99,5.25 6.49,5.5 0.5,0.25 10 false 1 - 2 6.083,5.49 6.354,5.708 0.271,0.219 10 false 2 5.99,5.698 6.49,5.917 0.5,0.219 10 false 2 - 3 6.083,5.917 6.354,6.135 0.271,0.219 10 false 3 5.99,6.146 6.313,6.323 0.323,0.177 10 false 3 - 4 6.094,6.365 6.344,6.563 0.25,0.198 10 false 4


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMMIN Made A
for TMT Made B



A

2.INSPECT HEATER RELAY

B

13.INSPECT HTR RELAY
2.INSPECT HEATER RELAY
a.

Remove the heater relay.



Result:
Proceed to
OK
NG



OK

3.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE HEATER RELAY

3.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Remove the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR(for TMMIN Made)>REMOVAL


b.

Inspect the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR(for TMMIN Made)>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT BLOWER RESISTOR

NG

4.INSPECT BLOWER RESISTOR


Result:
Proceed to
OK
NG



OK

5.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)

NG

5.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)

OK

6.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)

NG

6.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)
a.
E281479C04
0.333,0.771 0.76,1.01 0.427,0.24 0.427,0.781 0.885,0.979 0.458,0.198 10 false F78 0.115,0.104 0.573,0.302 0.458,0.198 10 false *1
*1 Heater Relay Holder


Remove the heater relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F78-2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
F78-5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HEATER RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEATER RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Remove the heater relay.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-3 - F53-2 Always Below 1 Ω
F78-3 or F53-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the F55 blower resistor connector.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-4 (HI) - F53-1 Always Below 1 Ω
F55-1 (E) - Body ground Always Below 1 Ω
F55-4 (HI) or F53-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Disconnect the F53 blower motor with fan sub-assembly connector.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F53-1 - F5-5 (HI) Always Below 1 Ω
F53-1 or F5-5 (HI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)
a.

Disconnect the F5 heater control and accessory assembly connector.


b.

Disconnect the F55 blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F5-6 (M2) - F55-2 (M2) Always Below 1 Ω
F5-1 (M1) - F55-3 (M1) Always Below 1 Ω
F5-10 (E) - Body ground Always Below 1 Ω
F5-6 (M2) or F55-2 (M2) - Body ground Always 10 kΩ or higher
F5-1 (M1) or F55-3 (M1) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (Through No. 9 Junction Connector) A
OK (Not Through No. 9 Junction Connector) B
NG C



A

11.CHECK HARNESS AND CONNECTOR (HEATER RELAY - HEATER CONTROL AND ACCESSORY ASSEMBLY AND AIR CONDITIONING AMPLIFIER ASSEMBLY)

B

12.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - HEATER RELAY AND HEATER CONTROL AND ACCESSORY ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HEATER RELAY - HEATER CONTROL AND ACCESSORY ASSEMBLY AND AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the heater relay.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Disconnect the F124 air conditioning amplifier assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-1 - F5-3 (LO) Always Below 1 Ω
F78-1 - F124-20 (HR) Always Below 1 Ω
F78-1 - F124-26 (SBLW) Always Below 1 Ω
F78-1 or F5-3 (LO) - Body ground Always 10 kΩ or higher
F78-1 or F124-20 (HR) - Body ground Always 10 kΩ or higher
F78-1 or F124-26 (SBLW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - HEATER RELAY AND HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Remove the heater relay.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Disconnect the F124 air conditioning amplifier assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-20 (HR) - F78-1 Always Below 1 Ω
F124-26 (SBLW) - F5-3 (LO) Always Below 1 Ω
F124-20 (HR) or F78-1 - Body ground Always 10 kΩ or higher
F124-26 (SBLW) or F5-3 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT HTR RELAY
a.

Remove the HTR relay from the No. 3 relay block.



Result:
Proceed to
OK
NG



OK

14.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE HTR RELAY

14.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Remove the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR(for TMT Made)>REMOVAL


b.

Inspect the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR(for TMT Made)>INSPECTION


Result:
Proceed to
OK
NG



OK

15.INSPECT BLOWER RESISTOR

NG

15.INSPECT BLOWER RESISTOR


Result:
Proceed to
OK
NG



OK

16.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)

NG

16.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)

OK

17.CHECK HARNESS AND CONNECTOR (HTR RELAY - POWER SOURCE)

NG

17.CHECK HARNESS AND CONNECTOR (HTR RELAY - POWER SOURCE)
a.

Remove the HTR relay from the No. 3 relay block.


b.
E371818C01
0.115,0.167 0.427,0.323 0.313,0.156 10 false *1 1.625,0.354 1.938,0.51 0.313,0.156 10 false *a
*1 No. 3 Relay Block
*a HTR Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (HTR RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (HTR RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Remove the HTR relay from the No. 3 relay block.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - F53-2 Always Below 1 Ω
Relay terminal 3 or F53-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the F55 blower resistor connector.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F55-4 (HI) - F53-1 Always Below 1 Ω
F55-1 (E) - Body ground Always Below 1 Ω
F55-4 (HI) or F53-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F55-1 (HI) - F53-1 Always Below 1 Ω
F55-4 (E) - Body ground Always Below 1 Ω
F55-1 (HI) or F53-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Disconnect the F53 blower motor with fan sub-assembly connector.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F53-1 - F5-5 (HI) Always Below 1 Ω
F53-1 or F5-5 (HI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)
a.

Disconnect the F5 heater control and accessory assembly connector.


b.

Disconnect the F55 blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F5-10 (M2) - F55-2 (M2) Always Below 1 Ω
F5-9 (M1) - F55-3 (M1) Always Below 1 Ω
F5-1 (E) - Body ground Always Below 1 Ω
F5-10 (M2) or F55-2 (M2) - Body ground Always 10 kΩ or higher
F5-9 (M1) or F55-3 (M1) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
F5-10 (M2) - F55-3 (M2) Always Below 1 Ω
F5-8 (M1) - F55-2 (M1) Always Below 1 Ω
F5-1 (E) - Body ground Always Below 1 Ω
F5-10 (M2) or F55-3 (M2) - Body ground Always 10 kΩ or higher
F5-8 (M1) or F55-2 (M1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - HTR RELAY AND HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - HTR RELAY AND HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Remove the HTR relay from the No. 3 relay block.


b.

Disconnect the F124 air conditioning amplifier assembly connector.


c.

Disconnect the F5 heater control and accessory assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F124-20 (HR) - Relay terminal 1 Always Below 1 Ω
F124-26 (SBLW) - F5-7 (LO) Always Below 1 Ω
F124-20 (HR) or Relay terminal 1 - Body ground Always 10 kΩ or higher
F124-26 (SBLW) or F5-7 (LO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F124-20 (HR) - Relay terminal 1 Always Below 1 Ω
F124-26 (SBLW) - F5-8 (LO) Always Below 1 Ω
F124-20 (HR) or Relay terminal 1 - Body ground Always 10 kΩ or higher
F124-26 (SBLW) or F5-8 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR