67872
1.INSTALL REAR DOOR WEATHERSTRIP
Engage the clamp and the 16 clips, and install the rear door weatherstrip.
68630
2.INSTALL REAR DOOR CHECK ASSEMBLY
Apply MP grease to the sliding parts of the rear door check assembly.
| *a | Door Panel Side |
| *b | Body Panel Side |
Install the rear door check assembly onto the door panel side with the 2 bolts.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the rear door check assembly onto the body panel side with the bolt.
69204A
3.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
| *a | Grommet |
| *b | Guide |
Engage the guide and the grommet, and install the rear door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.
69242G
4.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
Engage the 2 claws and install the rear door outside handle rear pad.
69241G
5.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
Engage the 2 claws and install the rear door outside handle front pad.
Using a T30 "TORX" socket wrench, tighten the screw.
69240
6.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Install the rear door outside handle assembly in the direction indicated by the arrow as shown in the illustration.
69227L
7.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the 2 guides and the 2 claws, and install the rear door outside handle cover.
Using a T30 "TORX" socket wrench, tighten the screw.
69340
8.INSTALL REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock)
69340
9.INSTALL REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock)
10.INSTALL HOLE PLUG (w/o Power Door Lock)
Install the hole plug.
68189
11.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP
Install the rear door quarter window weatherstrip to the rear door quarter window glass.
68124B
12.INSTALL REAR DOOR QUARTER WINDOW GLASS
Install the rear door quarter window glass with rear door quarter window weatherstrip in the direction indicated by the arrow as shown in the illustration.
69840A
13.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)
Apply MP grease to the sliding parts of the rear door window regulator assembly.
| *a | Temporary Bolt |
Temporarily install the temporary bolt to the rear door window regulator assembly.
Temporarily install the rear door window regulator assembly.
Install the rear door window regulator assembly with the 3 bolts and tighten the temporary bolt.
Connect the connector.
69840A
14.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)
Install the rear door window regulator assembly with the 3 bolts.
68104
15.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Insert the rear door glass sub-assembly into the rear door panel in the direction indicated by the arrow as shown in the illustration.
Do not damage the rear door glass sub-assembly.
Install the rear door glass sub-assembly to the rear door window regulator assembly as shown in the illustration.
Do not damage the rear door glass sub-assembly.
67408H
16.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Install the screw.
Make sure to return the rear door weatherstrip to its original condition after performing this step.
Peel back the rear door weatherstrip to install the screw.
Install the rear door window division bar sub-assembly with the 2 bolts.
When installing rear door window division bar sub-assembly, do not allow the rear door quarter window glass to fall.
67842E
17.INSTALL REAR DOOR SERVICE HOLE COVER
Apply new butyl tape to the rear door panel.
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
| *a | Reference Point |
Install the rear door service hole cover according to the reference points on the rear door panel.
Securely install the rear door service hole cover, taking care to prevent wrinkles and air bubbles.
Connect each connector.
67674A
18.INSTALL REAR DOOR FRAME GARNISH
Engage the clamp and install a new rear door frame garnish.
68152C
19.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
68174A
20.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
Install the rear door glass inner weatherstrip.
75924
21.INSTALL NO. 2 BLACK OUT TAPE
75762A
22.INSTALL REAR DOOR WINDOW FRAME FRONT MOULDING
68230C
23.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
86160B
24.INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)
69206C
25.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 4 guides and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
67604
26.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
Engage the 2 guides and connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door trim board sub-assembly.
Engage the 6 claws and the guide.
Engage the 7 clips and install the rear door trim board sub-assembly.
Install the 3 screws.
Engage the claw and close the door inside handle bezel plug.
74272A
27.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)
Connect the connector.
Engage the 7 claws and install the rear door armrest base upper panel.
74272A
28.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)
Engage the 5 claws and install the rear door armrest base upper panel.
69260E
29.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
Install the rear door window regulator handle assembly and fully open the rear door glass sub-assembly.
Remove the rear door window regulator handle assembly.
| *a | Door Panel Side |
| *b | Inside of Vehicle |
Install the window regulator handle plate as shown in the illustration.
| *a | Front of Vehicle |
| *b | Assemble with Glass in Fully Open Position |
Install the rear door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.
30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (for Hatchback).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION