| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1422 | Master Cylinder Pressure Sensor Zero Point High Malfunction | When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more. | ·
Stop light switch assembly ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) ·
Brake actuator assembly (Master cylinder pressure sensor) |
Refer to DTC C1425.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).
Check for DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1422 is output | A |
| DTCs C1422 and C1425 are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly | ON or OFF | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Tester Display |
|---|
| Stop Light SW |
Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Master Cylinder Sensor | Master cylinder pressure sensor reading | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.30 to 0.80 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Master Cylinder Sensor |
Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.
When the pedal is depressed, the voltage displayed on the GTS increases.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1422 is not output | A |
| DTC C1422 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation.
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT
The brake pedal height and stop light switch assembly installation are normal.
| Result | Proceed to |
|---|---|
| OK (for Bulb Type Stop Light) | A |
| OK (for LED Type Stop Light) | B |
| NG (for RHD) | C |
| NG (for LHD) | D |
A
B
C
D
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except LHD with Continuously Variable Transaxle |
| *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A48-2 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8 to 14 V |
| A48-2 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A49-2 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8 to 14 V |
| A49-2 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except LHD with Continuously Variable Transaxle |
| *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A48-2 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8 to 14 V |
| A48-2 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A49-2 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8 to 14 V |
| A49-2 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG