Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090850 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal*1 or clutch pedal*2 is depressed and the electrical key transmitter sub-assembly is held near the engine switch.

·

When the smart key cancel function has been canceled on the customization menu, the brake pedal*1 or clutch pedal*2 is depressed and the electrical key transmitter sub-assembly is held near the engine switch.

*1: for CVT

*2: for Manual Transaxle



Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG Relay Monitor(Inside)

·

IG Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-

WIRING DIAGRAM

E373869E05
0.167,0.521 2,0.719 1.833,0.198 10 false from Battery 1.365,6.656 3.198,6.854 1.833,0.198 10 false from Battery 0.083,1.104 0.969,1.625 0.885,0.521 10 false from D/C CUT Fuse 1.5,0.688 3.333,0.885 1.833,0.198 10 false AM2 NO. 2 1.646,1.313 3.479,1.51 1.833,0.198 10 false DOME 2.906,0.531 4.74,0.729 1.833,0.198 10 false +B 5.885,0.521 7.156,0.74 1.271,0.219 10 false from AM1 Fuse 5.885,4.417 7.156,4.635 1.271,0.219 10 false from AM2 Fuse 6.542,2.854 7.146,3.104 0.604,0.25 10 false to Fuse 6.531,1.25 7.135,1.5 0.604,0.25 10 false to Fuse 4.833,4.167 6.135,4.354 1.302,0.188 10 false No. 4 Relay Block 5.271,1.969 5.646,2.188 0.375,0.219 10 false IG1 3.729,1.656 4.177,1.917 0.448,0.26 10 false F43 3.76,1.479 4.208,1.74 0.448,0.26 10 false 20 3.323,1.667 3.771,1.927 0.448,0.26 10 false IG1D 2.906,1.167 3.354,1.427 0.448,0.26 10 false CUTB 2.896,1.708 3.344,1.969 0.448,0.26 10 false E 2.885,2.469 3.333,2.729 0.448,0.26 10 false SSW1 2.906,2.906 3.354,3.167 0.448,0.26 10 false SSW2 2.896,3.344 3.344,3.604 0.448,0.26 10 false AGND 2.583,0.521 3.031,0.781 0.448,0.26 10 false F43 2.573,1.698 3.021,1.958 0.448,0.26 10 false F43 2.583,2.448 3.031,2.708 0.448,0.26 10 false F43 2.573,2.885 3.021,3.146 0.448,0.26 10 false F43 2.573,3.333 3.021,3.594 0.448,0.26 10 false F43 0.656,3.656 1.104,3.917 0.448,0.26 10 false F13 0.667,3.844 1.729,4.073 1.063,0.229 10 false Engine Switch 2.573,1.146 3.021,1.406 0.448,0.26 10 false F44 1.188,2.479 1.635,2.74 0.448,0.26 10 false SS1 1.188,2.885 1.635,3.146 0.448,0.26 10 false SS2 1.073,3.344 1.521,3.604 0.448,0.26 10 false AGND 2.917,4.365 3.542,4.563 0.625,0.198 10 false STP1*1 2.906,5.792 3.531,5.99 0.625,0.198 10 false STP1*2 3.26,6.146 3.885,6.344 0.625,0.198 10 false ACCD 4.958,1.135 5.406,1.396 0.448,0.26 10 false 5 5.74,1.146 6.188,1.406 0.448,0.26 10 false 3 5.74,1.542 6.188,1.802 0.448,0.26 10 false 2 4.969,1.531 5.417,1.792 0.448,0.26 10 false 1 5.76,3.146 6.208,3.406 0.448,0.26 10 false 1 4.958,3.146 5.406,3.406 0.448,0.26 10 false 2 4.948,2.719 5.396,2.979 0.448,0.26 10 false 3 5.74,2.698 6.188,2.958 0.448,0.26 10 false 5 2.573,4.333 3.021,4.594 0.448,0.26 10 false F43 2.573,5.771 3.021,6.031 0.448,0.26 10 false F43 3.729,6.156 4.177,6.417 0.448,0.26 10 false F43 4.354,6.885 6.938,7.198 2.583,0.313 10 false Driver Side Junction Block Assembly 4.969,6.5 5.417,6.76 0.448,0.26 10 false ACC 5.542,5.906 6.594,6.146 1.052,0.24 10 false SFT LOCK-ACC 4.26,5.74 4.708,6 0.448,0.26 10 false 6A 4.281,6.167 4.729,6.427 0.448,0.26 10 false 6F 4.302,5.542 4.75,5.802 0.448,0.26 10 false 1 4.302,5.99 4.75,6.25 0.448,0.26 10 false 2 6.542,6.156 6.99,6.417 0.448,0.26 10 false 6J 6.573,5.979 7.021,6.24 0.448,0.26 10 false 8 6.542,5.75 6.99,6.01 0.448,0.26 10 false 6L 6.573,5.563 7.021,5.823 0.448,0.26 10 false 5 2.479,6.802 4,7.281 1.521,0.479 10 false Certification ECU (Smart Key ECU Assembly) 0.521,6.823 1.01,7.188 0.49,0.365 10 false STOP 0.604,5.948 1.094,6.313 0.49,0.365 10 false A21*2 0.521,5.667 1.01,6.031 0.49,0.365 10 false *2 0.115,5.365 0.604,5.729 0.49,0.365 10 false *1 0.521,4.958 1.01,5.323 0.49,0.365 10 false A58*1 0.51,5.135 2.354,5.448 1.844,0.313 10 false Stop Light Switch Assembly 0.563,6.146 2.406,6.458 1.844,0.313 10 false Stop Light Switch Assembly 1.125,5.667 1.573,5.927 0.448,0.26 10 false B 1.708,5.667 2.156,5.927 0.448,0.26 10 false 1 0.917,5.677 1.365,5.938 0.448,0.26 10 false 2 1.531,5.667 1.979,5.927 0.448,0.26 10 false L 0.99,4.771 1.438,5.031 0.448,0.26 10 false B 1.333,4.323 1.781,4.583 0.448,0.26 10 false OUT 1.323,4.781 1.771,5.042 0.448,0.26 10 false GND 1.729,4.229 2.177,4.49 0.448,0.26 10 false 2 0.781,4.635 1.229,4.896 0.448,0.26 10 false 1 1.729,4.635 2.177,4.896 0.448,0.26 10 false 3 1.563,2.75 2.01,3.01 0.448,0.26 10 false 1 1.563,2.333 2.01,2.594 0.448,0.26 10 false 5 1.552,3.198 2,3.458 0.448,0.26 10 false 6 2.604,5.583 3.052,5.844 0.448,0.26 10 false 11 2.615,4.156 3.063,4.417 0.448,0.26 10 false 11 2.615,3.156 3.063,3.417 0.448,0.26 10 false 24 2.615,2.708 3.063,2.969 0.448,0.26 10 false 16 2.625,2.26 3.073,2.521 0.448,0.26 10 false 18 2.615,1.5 3.063,1.76 0.448,0.26 10 false 10 2.615,0.958 3.063,1.219 0.448,0.26 10 false 33 2.635,0.333 3.083,0.594 0.448,0.26 10 false 1 3.76,5.979 4.208,6.24 0.448,0.26 10 false 21 0.354,7.448 2.719,7.781 2.365,0.333 10 false *1: for LED Type Stop Light with CVT 2.927,7.448 5.417,7.729 2.49,0.281 10 false *2: for Bulb Type Stop Light with CVT 5.271,3.594 5.646,3.813 0.375,0.219 10 false IG2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press the lock or unlock switch of the electrical key transmitter sub-assembly and check the transmitter LED illuminates.

OK:

Transmitter LED illuminates.




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

25.INSPECT TRANSMITTER BATTERY (VOLTAGE)
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted Yes or No Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

OK:

"NO" is displayed in the Data List.


Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE SWITCH CONDITION

NG

3.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.

*1: for CVT

*2: for Manual Transaxle


OK:

The power source mode changes.



Result:
Result Proceed to
NG A
OK B



A

4.CHECK SMART ENTRY AND START SYSTEM

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK SMART ENTRY AND START SYSTEM
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


b.
B342596C02
0.729,0.438 1.219,0.677 true 2.323,0.719 2.635,0.49 true 0.542,0.333 0.802,0.573 0.26,0.24 11 false *1 2.677,0.385 2.938,0.625 0.26,0.24 11 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.

*1: for CVT

*2: for Manual Transaxle


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


OK:

The power source mode changes.



Result:
Result Proceed to
The power source mode does not change A
The power source mode changes B



A

5.CHECK FOR DTC

B

22.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
5.CHECK FOR DTC
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO DTC CHART

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

7.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

7.CHECK HARNESS AND CONNECTOR (GROUND)

OK

8.INSPECT IG1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IG1 RELAY
a.

Remove the IG1 relay.


b.
B344996E01
1.969,0.906 2.302,1.083 true 2.427,0.24 2.604,0.604 true 2.917,1.094 3.229,0.917 true 2.615,1.635 2.823,1.917 true 3.26,0.823 3.417,1.021 0.156,0.198 10 false 1 2.302,0.135 2.458,0.333 0.156,0.198 10 false 3 1.844,0.823 2,1.021 0.156,0.198 10 false 2 2.813,1.958 2.969,2.156 0.156,0.198 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (IG1 RELAY))

NG

REPLACE IG1 RELAY

9.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (IG1 RELAY))
a.

Remove the IG1 relay from No. 4 relay block.


b.

Measure the voltage according to the value(s) in the table below.

E377752C01
0.375,0.26 0.75,0.5 0.375,0.24 12 false *A 3.833,0.26 4.208,0.5 0.375,0.24 12 false *B 1.573,0.354 1.948,0.594 0.375,0.24 10 false *2 4.333,0.833 4.708,1.073 0.375,0.24 10 false *1 4.938,0.375 5.313,0.615 0.375,0.24 10 false *2 0.698,0.531 1.073,0.771 0.375,0.24 10 false *1
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 IG1 Relay Holder


Standard Voltage:
Tester Connection Condition Specified Condition
IG1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IG1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (IG1 RELAY - BODY GROUND)
a.

Remove the IG1 relay from No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

E377752C01
0.375,0.26 0.75,0.5 0.375,0.24 12 false *A 3.833,0.26 4.208,0.5 0.375,0.24 12 false *B 1.573,0.354 1.948,0.594 0.375,0.24 10 false *2 4.333,0.833 4.708,1.073 0.375,0.24 10 false *1 4.938,0.375 5.313,0.615 0.375,0.24 10 false *2 0.698,0.531 1.073,0.771 0.375,0.24 10 false *1
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 IG1 Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
IG1 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (IG1 RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (IG1 RELAY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG1 relay from No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - IG1 relay terminal 1 Always Below 1 Ω
F43-20 (IG1D) or IG1 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT IG2 RELAY
a.

Remove the IG2 relay from No. 4 relay block.


b.
A232574E13
2.313,0.76 1.938,0.479 true 2.896,0.677 3.208,0.469 true 2.792,1.115 3.188,1.115 true 2.802,1.594 3.177,1.594 true 1.823,0.385 1.927,0.542 0.104,0.156 10 1 3.271,0.385 3.375,0.542 0.104,0.156 10 2 3.229,1.531 3.333,1.688 0.104,0.156 10 3 3.24,1.042 3.344,1.198 0.104,0.156 10 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (IG2 RELAY))

NG

REPLACE IG2 RELAY

13.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (IG2 RELAY))
a.

Remove the IG2 relay from No. 4 relay block.


b.

Measure the voltage according to the value(s) in the table below.

E377753C01
0.24,0.229 0.615,0.469 0.375,0.24 12 false *A 4,0.281 4.375,0.521 0.375,0.24 12 false *B 4.219,0.854 4.594,1.094 0.375,0.24 10 false *1 0.604,0.51 0.979,0.75 0.375,0.24 10 false *1 1.563,0.344 1.938,0.583 0.375,0.24 10 false *2 4.802,0.417 5.177,0.656 0.375,0.24 10 false *2
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 IG2 Relay Holder


Standard Voltage:
Tester Connection Condition Specified Condition
IG2 relay terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)
a.

Remove the IG2 relay from No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

E377753C01
0.24,0.229 0.615,0.469 0.375,0.24 12 false *A 4,0.281 4.375,0.521 0.375,0.24 12 false *B 4.219,0.854 4.594,1.094 0.375,0.24 10 false *1 0.604,0.51 0.979,0.75 0.375,0.24 10 false *1 1.563,0.344 1.938,0.583 0.375,0.24 10 false *2 4.802,0.417 5.177,0.656 0.375,0.24 10 false *2
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 IG2 Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (IG2 RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (IG2 RELAY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 relay from No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - IG2 relay terminal 2 Always Below 1 Ω
F43-20 (IG1D) or IG2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B342624C25
1.031,0.333 1.417,0.583 0.385,0.25 2.615,0.333 3,0.583 0.385,0.25 4.167,0.333 4.552,0.583 0.385,0.25 5.75,0.333 6.135,0.583 0.385,0.25 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 1.135,0.365 1.448,0.563 0.313,0.198 10 false 6A 2.729,0.365 3.042,0.563 0.313,0.198 10 false 6L 4.281,0.365 4.594,0.563 0.313,0.198 10 false 6F 5.865,0.365 6.177,0.563 0.313,0.198 10 false 6J
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
6A-1 - 6L-5 Battery voltage not applied to terminals 6F-2 and 6J-8 10 kΩ or higher
Battery voltage applied to terminals 6F-2 and 6J-8 Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 6F and 6J driver side block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-21 (ACCD) - 6F-2 Always Below 1 Ω
6J-8 - Body ground Always Below 1 Ω
F43-21 (ACCD) or 6F-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the F43 certification ECU (smart key ECU assembly) connector.


b.

Connect the 6F and 6J driver side junction block assembly connectors.

E374147C25
2.417,0.417 2.917,0.667 0.5,0.25 3.125,2.385 2.5,1.49 true 1.99,2.354 2.448,1.49 true 0.188,0.302 0.5,0.5 0.313,0.198 10 false *a 2.542,0.458 3.073,0.781 0.531,0.323 10 false F43 3.042,2.417 3.458,2.635 0.417,0.219 10 false IG1D 1.802,2.396 2.219,2.615 0.417,0.219 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

d.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F43-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
F43-21 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (IG) 8.5 V or higher
Engine switch on (ACC) 8.5 V or higher



Result:
Result Proceed to
NG A
OK B



A

19.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

B

19.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.



Result:
Result Proceed to
NG A
OK B



A

20.INSPECT ENGINE SWITCH

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.INSPECT ENGINE SWITCH


Result:
Result Proceed to
OK A
NG (for 1NR-FE LHD) B
NG (for 2NR-FE LHD) C
NG (for 1NR-FE RHD) D
NG (for 2NR-FE RHD) E



A

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

B

C

D

E

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F13 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-18 (SSW1) - F13-5 (SS1) Always Below 1 Ω
F43-16 (SSW2) - F13-1 (SS2) Always Below 1 Ω
F43-24 (AGND) - F13-6 (AGND) Always Below 1 Ω
F43-18 (SSW1) or F13-5 (SS1) - Body ground Always 10 kΩ or higher
F43-16 (SSW2) or F13-1 (SS2) - Body ground Always 10 kΩ or higher
F43-24 (AGND) or F13-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.



Result:
Result Proceed to
NG A
OK B



A

23.INSPECT ENGINE SWITCH

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

23.INSPECT ENGINE SWITCH


Result:
Result Proceed to
OK A
NG (for 1NR-FE LHD) B
NG (for 2NR-FE LHD) C
NG (for 1NR-FE RHD) D
NG (for 2NR-FE RHD) E



A

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

B

C

D

E

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F13 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-18 (SSW1) - F13-5 (SS1) Always Below 1 Ω
F43-16 (SSW2) - F13-1 (SS2) Always Below 1 Ω
F43-24 (AGND) - F13-6 (AGND) Always Below 1 Ω
F43-18 (SSW1) or F13-5 (SS1) - Body ground Always 10 kΩ or higher
F43-16 (SSW2) or F13-1 (SS2) - Body ground Always 10 kΩ or higher
F43-24 (AGND) or F13-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery.

i.

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


ii.
B327509C08
2.76,0.906 3.073,0.448 false 3.104,0.313 3.323,0.521 0.219,0.208 10 false *a
*a Lead Wire


Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B327510C02
2.365,1.115 1.688,0.375 false 1.49,0.281 1.802,0.479 0.313,0.198 10 false *a
*a GND


Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST



Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Engine switch off, all doors closed and trigger switch pressed 2.3 to 3.2 V




Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG