Refer to DTC P001013.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P001013
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P001107 | Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure | 10° CA or greater camshaft timing gear assembly run-out maintained for 3 seconds or longer for 2 times (1 trip detection logic). | ·
Cam timing oil control solenoid assembly (for intake camshaft) ·
Camshaft timing gear bolt (intake camshaft timing oil control valve) ·
Camshaft timing gear assembly ·
ECM |
Comes on | DTC stored | SAE: P0011 |
During idling, the camshaft timing gear is locked at the center of the variable valve timing operating range by the two lock pins. The camshaft timing gear assembly run-out increases if one lock pin is stuck in the retracted position. In this case, the ECM illuminates the MIL and stores this DTC.
| Required Sensors/Components (Main) | Cam timing oil control solenoid assembly (for intake camshaft)
Camshaft timing gear bolt (intake camshaft timing oil control valve) Camshaft timing gear assembly |
| Required Sensors/Components (Related) | Crankshaft position sensor
Camshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Wait 20 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P001107.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P001013.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P001013
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Pre-procedure1
Start the engine.
Procedure1
Check for abnormal noise (rattling sounds) from the camshaft timing gear assembly with the engine idling.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| Abnormal noise (rattling sound) from the camshaft timing gear assembly is heard. | A |
| Abnormal noise (rattling sound) from the camshaft timing gear assembly is not heard. | B |
As the engine speed increases, the camshaft timing gear assembly lock pins will release and the abnormal noise (rattling sound) will disappear.
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE): Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE (for Intake Side)>REMOVAL
CAMSHAFT TIMING GEAR ASSEMBLY: Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL
B
Read the Data List while performing the Active Test with the engine idling.
| Active Test Display |
|---|
| Control the Intake VVT OCV Duty Ratio Bank 1 |
| Data List Display |
|---|
| Intake VVT Change Angle Bank 1 |
| Intake VVT OCV Control Duty Ratio Bank 1 |
| GTS Operation | Data List (Intake VVT Change Angle Bank 1) |
|---|---|
| -100% to 100% | Varies by 30 DegFR or more |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P001107.
Check the DTC judgment result.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P001107 is output) |
B |
A
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Start the engine.
Procedure1
Read the Data List while performing the Active Test with the engine idling.
| Active Test Display |
|---|
| Control the Intake VVT OCV Duty Ratio Bank 1 |
| Data List Display |
|---|
| Intake VVT Change Angle Bank 1 |
| Intake VVT OCV Control Duty Ratio Bank 1 |
| GTS Operation | Data List (Intake VVT Change Angle Bank 1) |
|---|---|
| -100% to 100% | Varies by 30 DegFR or more |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P001107.
Check the DTC judgment result.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P001107 is output) |
B |
A
B