Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0ABF11  Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground  P0ABF15  Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open  P0B0E11  Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground  P0B0E15  Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open  P1CBB12  Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery  P1CBB14  Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open  


DESCRIPTION

A battery current sensor, which is mounted on the positive cable side of each HV battery junction block assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery ECU assembly. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, to the IB1 terminal of the battery ECU assembly. When the voltage at the IB0 terminal is below 2.57 V and the voltage at the IB1 terminal is above 2.43 V, this indicates that the HV battery is being discharged. Additionally, Meanwhile, when the voltage at of the IB0 terminal is above 2.57 V and the voltage at of he IB1 terminal is below 2.43 V, this indicates that the HV battery is being charged. The battery ECU assembly determines the charging and discharging amount of the HV battery based on the voltages input to the IB0 terminal and IB1 terminal and calculates the SOC of the HV battery through the accumulated amperage.

A460750E02
0.177,0.188 0.781,0.563 0.604,0.375 10 false Charging Current 1.167,0.167 1.958,0.552 0.792,0.385 10 false Discharging Current 1.219,1.26 2.177,1.615 0.958,0.354 10 false Battery Current Sensor 2.156,2.927 2.99,3.323 0.833,0.396 10 false Battery ECU Assembly 2.229,1.792 2.49,1.99 0.26,0.198 10 false VIB 2.229,1.979 2.49,2.177 0.26,0.198 10 false IB0 2.208,2.156 2.469,2.354 0.26,0.198 10 false GIB 2.219,2.323 2.479,2.521 0.26,0.198 10 false IB1 3.719,0.448 6.448,0.677 2.729,0.229 10 false Battery Current Sensor Output Voltage (V) 3.042,1.917 3.375,2.104 0.333,0.188 10 false (IB1) 6.802,2 7.135,2.188 0.333,0.188 10 false (IB0) 5.115,2.51 5.448,2.698 0.333,0.188 10 false IB0 5.896,1.802 6.229,1.99 0.333,0.188 10 false IB1 3.219,3.167 3.823,3.542 0.604,0.375 10 false Charging Current 6.302,3.188 7.094,3.573 0.792,0.385 10 false Discharging Current 4.219,3.458 5.948,3.688 1.729,0.229 10 false Hybrid Battery Current (A) 3.406,2.688 3.635,2.875 0.229,0.188 10 false 0.3 3.333,2.063 3.646,2.25 0.313,0.188 10 false 2.43 3.406,1.198 3.635,1.385 0.229,0.188 10 false 4.7 6.521,1.229 6.792,1.417 0.271,0.188 10 false 4.6 6.521,1.854 6.833,2.042 0.313,0.188 10 false 2.57 6.521,2.677 6.833,2.865 0.313,0.188 10 false 0.4 3.74,2.99 4.052,3.177 0.313,0.188 10 false -290 6.146,2.99 6.552,3.177 0.406,0.188 10 false +310 4.844,3 4.979,3.177 0.135,0.177 10 false 0

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground The battery current sensor output voltage (IB0) is excessively low.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open The battery current sensor output voltage (IB0) is excessively high.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground The battery current sensor output voltage (IB1) is excessively low.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open The battery current sensor output voltage (IB1) is excessively high.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery Power source voltage (VIB) of the battery current sensor is excessively high.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open Power source voltage (VIB) of the battery current sensor is excessively low.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0ABF11 Hybrid/EV Battery Current
P0ABF15
P0B0E11
P0B0E15
P1CBB12
P1CBB14

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A459771E05
1.792,0.51 2.344,0.927 0.552,0.417 10 false VIB 2.125,0.5 2.813,0.906 0.688,0.406 10 false 1 1.823,1.156 2.375,1.573 0.552,0.417 10 false IB0 1.833,1.792 2.385,2.208 0.552,0.417 10 false IB1 1.792,2.427 2.344,2.844 0.552,0.417 10 false GIB 2.115,1.156 2.802,1.563 0.688,0.406 10 false 4 2.146,1.802 2.833,2.208 0.688,0.406 10 false 2 2.125,2.417 2.813,2.823 0.688,0.406 10 false 3 0.365,2.906 2.281,3.177 1.917,0.271 10 false z11 5.125,0.5 5.677,0.917 0.552,0.417 10 false VIB 5.125,1.146 5.677,1.563 0.552,0.417 10 false IB0 5.146,1.792 5.698,2.208 0.552,0.417 10 false IB1 5.125,2.438 5.677,2.854 0.552,0.417 10 false GIB 4.875,3.135 6.667,3.604 1.792,0.469 10 false z12 Battery ECU Assembly 4.885,0.521 5.573,0.927 0.688,0.406 10 false 31 4.885,1.156 5.573,1.563 0.688,0.406 10 false 19 4.958,1.781 5.646,2.188 0.688,0.406 10 false 8 4.969,2.417 5.656,2.823 0.688,0.406 10 false 7 0.365,3.104 2.552,3.51 2.188,0.406 10 false No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output A
P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output and DTCs other than the DTCs in the table below are output B
P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output and hybrid battery system DTCs in the table below are output C
P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output and hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)

B

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)

C

D

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.


e.

Turn the ignition switch to ON.


Procedure1

f.
A459571C06
1.49,0.115 1.948,0.427 0.458,0.313 1.729,2.844 2.073,2.219 true 2.583,2.875 2.281,2.115 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.521,2.917 3.146,3.167 0.625,0.25 10 false IGCT 1.583,2.917 2.021,3.115 0.438,0.198 10 false GND
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-24 (IGCT) - z12-34 (GND) Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




Post-procedure1

g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the z12 battery ECU assembly connector.


j.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

e.
A459831C01
0.094,1.177 0.51,1.458 0.417,0.281 0.146,3.542 0.563,3.823 0.417,0.281 0.823,2.521 1.771,1.625 true 2.573,2.552 1.875,1.635 true 1.219,2.51 1.76,1.729 true 1.938,2.542 1.771,1.854 true 2.458,4.24 1.823,3.885 true 1.594,3.604 0.958,3.25 true 1.594,3.885 0.969,4.167 true 2.469,3.333 1.844,3.615 true 1.135,2.573 1.594,2.771 0.458,0.198 10 false IB0 1.854,2.604 2.313,2.802 0.458,0.198 10 false VIB 2.51,2.604 2.969,2.802 0.458,0.198 10 false IB1 0.708,2.563 1.167,2.76 0.458,0.198 10 false GIB 0.198,1.26 0.656,1.458 0.458,0.198 10 false z12 0.729,3.177 1.188,3.375 0.458,0.198 10 false VIB 0.729,4.135 1.188,4.333 0.458,0.198 10 false GIB 2.531,3.25 2.99,3.448 0.458,0.198 10 false IB1 2.552,4.219 3.01,4.417 0.458,0.198 10 false IB0 0.25,3.604 0.708,3.802 0.458,0.198 10 false z11 0.094,0.167 0.406,0.365 0.313,0.198 10 false *a 0.177,2.927 0.49,3.125 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z12-8 (IB1) - z11-2 (IB1) Ignition switch off Below 1 Ω
z12-7 (GIB) - z11-3 (GIB) Ignition switch off Below 1 Ω
z12-19 (IB0) - z11-4 (IB0) Ignition switch off Below 1 Ω
z12-31 (VIB) - z11-1 (VIB) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z12-8 (IB1) or z11-2 (IB1) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-7 (GIB) or z11-3 (GIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-19 (IB0) or z11-4 (IB0) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-31 (VIB) or z11-1 (VIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Post-procedure1

f.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.


g.

Reconnect the z12 battery ECU assembly connector.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

4.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

4.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

e.
A460457C01
0.281,3.271 0.708,3.635 0.427,0.365 1.885,3.438 2.302,3.021 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 2.365,2.938 2.823,3.135 0.458,0.198 10 false VIB 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z11-1 (VIB) - z11-3 (GIB) Ignition switch ON 4.6 to 5.4 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Post-procedure1

f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

5.CHECK BATTERY ECU ASSEMBLY (GIB - GND)

NG

13.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
5.CHECK BATTERY ECU ASSEMBLY (GIB - GND)

Pre-procedure1

a.

Remove the battery ECU assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

b.
A459830C02
0.948,2.365 1.365,2.667 0.417,0.302 0.833,3.979 1.198,3.458 true 2.031,3.958 1.635,3.177 true 0.094,0.042 0.552,0.24 0.458,0.198 10 false *a 0.708,4.021 1.167,4.219 0.458,0.198 10 false GND 1.031,2.458 1.49,2.656 0.458,0.198 10 false z12 1.948,4.021 2.406,4.219 0.458,0.198 10 false GIB
*a Component without harness connected
(Battery ECU Assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-34 (GND) - z12-7 (GIB) Ignition switch off Below 1 Ω



Post-procedure1

c.

Install the battery ECU assembly.


Result:
Proceed to
OK
NG



OK

6.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))

NG

6.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

e.
A460457C02
0.281,3.271 0.708,3.635 0.427,0.365 1.896,3.667 2.323,4.042 true 1.125,3.073 1.552,3.448 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 0.917,2.99 1.375,3.188 0.458,0.198 10 false IB1 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z11-2 (IB1) - z11-3 (GIB) Ignition switch ON 2.37 to 2.49 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Post-procedure1

f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

7.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))

NG

11.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
7.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

e.
A460457C03
0.281,3.271 0.708,3.635 0.427,0.365 1.146,4.083 1.563,3.667 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 0.927,4.042 1.385,4.24 0.458,0.198 10 false IB0 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z11-4 (IB0) - z11-3 (GIB) Ignition switch ON 2.51 to 2.63 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Post-procedure1

f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

NG

8.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
8.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

e.
A460457C03
0.281,3.271 0.708,3.635 0.427,0.365 1.146,4.083 1.563,3.667 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 0.927,4.042 1.385,4.24 0.458,0.198 10 false IB0 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Tester Connection Condition
z11-4 (IB0) - z11-3 (GIB) Ignition switch ON

NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Post-procedure1

f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery upper cover panel.


Result:
Result Proceed to
0.3 to 4.7 V A
Below 0.3 V B
4.7 V or higher C



A

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

B

9.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))

C

10.CHECK BATTERY ECU ASSEMBLY (VIB - IB0)
9.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

f.
A459467C04
2.333,1.135 2.729,1.365 0.396,0.229 1,1.771 1.625,1.385 true 2.365,1.802 1.781,1.375 true 2.438,1.771 2.771,2.01 0.333,0.24 10 false IB0 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z11
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z11-4 (IB0) - z11-3 (GIB) Ignition switch ON 4.6 to 5.4 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Post-procedure1

g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.


j.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

10.CHECK BATTERY ECU ASSEMBLY (VIB - IB0)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

d.
A459467C02
1.5,0.24 1.896,0.469 0.396,0.229 1.604,1.052 0.99,0.906 true 2.406,1.521 1.792,1.375 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 2.5,1.5 2.865,1.75 0.365,0.25 10 false IB0 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 1.583,0.271 1.958,0.573 0.375,0.302 10 false z11
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
z11-1 (VIB) - z11-4 (IB0) Ignition switch off 10 kΩ or higher



Post-procedure1

e.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.


f.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

11.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

e.
A460457C02
0.281,3.271 0.708,3.635 0.427,0.365 1.896,3.667 2.323,4.042 true 1.125,3.073 1.552,3.448 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 0.917,2.99 1.375,3.188 0.458,0.198 10 false IB1 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
z11-2 (IB1) - z11-3 (GIB) Ignition switch ON


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Post-procedure1

f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the HV battery upper cover panel.


Result:
Result Proceed to
0.3 to 4.7 V A
Below 0.3 V B
4.7 V or higher C



A

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

B

12.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))

C

14.CHECK BATTERY ECU ASSEMBLY (VIB - IB1)
12.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

f.
A459467C05
2.333,1.135 2.729,1.365 0.396,0.229 1,1.771 1.625,1.385 true 1.833,1.063 2.458,0.677 true 2.51,0.594 2.844,0.833 0.333,0.24 10 false IB1 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z11
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z11-2 (IB1) - z11-3 (GIB) Ignition switch ON 4.6 to 5.4 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Post-procedure1

g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly


j.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

13.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY, unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

f.
A459467C01
2.333,1.135 2.729,1.365 0.396,0.229 1.604,1.052 0.99,0.906 true 1,1.771 1.625,1.385 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z11
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z11-1 (VIB) - z11-3 (GIB) Ignition switch ON 4.6 to 5.4 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Post-procedure1

g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.


j.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

14.CHECK BATTERY ECU ASSEMBLY (VIB - IB1)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.


Procedure1

d.
A459467C03
1.5,0.219 1.896,0.448 0.396,0.229 1.604,1.052 0.99,0.906 true 1.771,1.052 2.354,0.844 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 2.438,0.781 2.802,1.031 0.365,0.25 10 false IB1 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 1.594,0.24 1.969,0.542 0.375,0.302 10 false z11
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
z11-1 (VIB) - z11-2 (IB1) Ignition switch off 10 kΩ or higher



Post-procedure1

e.

Reconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.


f.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG