Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING ECU › 2020.03–2020.07
RM36W0E _55 Steering _087549 POWER ASSIST SYSTEMS _0424124 POWER STEERING ECU A

POWER ASSIST SYSTEMS  POWER STEERING ECU  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 45254B 1.INSTALL ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

a.
C346860C01
0,0 0,0 false
V100135

Grease


Apply grease to a new electric power steering motor shaft damper.

NOTICE:

First wipe off the existing grease from the serrated part, and then apply the dedicated grease supplied with a new power steering ECU with motor assembly or electric power steering column sub-assembly.



b.
C433973

Install the electric power steering motor shaft damper to the electric power steering column sub-assembly.


Hide 89650 2.INSTALL POWER STEERING ECU WITH MOTOR ASSEMBLY

NOTICE:
·

Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU with motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU with motor assembly.



a.
C433972

Temporarily install the power steering ECU with motor assembly to the electric power steering column sub-assembly with the 2 bolts.

NOTICE:

When temporarily installing the 2 bolts to the power steering ECU with motor assembly, do not tighten them all the way down.



b.
C399363

Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt to the steering main shaft.

NOTICE:

Do not apply excessive torque to the steering wheel assembly set bolt by using a tool such as an impact wrench.


HINT:

The steering wheel assembly set bolt is used for turning the steering main shaft during inspection of the steering main shaft rotating torque.

Remove the steering wheel assembly set bolt after performing this inspection.



c.
C432204C02
1.354,1.25 1.781,1.25 true 2.521,1.208 3.167,1.208 true 2.99,1.208 2.99,1.656 2.99,1.656 2.656,1.656 true 2.615,1.5 2.99,1.5 true 3.198,1.104 3.406,1.271 0.208,0.167 10 false *a 1.135,1.146 1.448,1.302 0.313,0.156 10 false *b
*a Wooden Block
*b Cloth


Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks.

NOTICE:
·

Do not overtighten the vise, as the steering column assembly may become deformed.

·

Secure the power steering ECU with motor assembly so that it is upright.

·

Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.




d.
C433974

Rotate the steering main shaft 180 degrees counterclockwise and then 180 degrees clockwise at a speed of 60 rpm, and repeat 2 to 3 times to center the axis of the power steering ECU with motor assembly. [*1]


e.
C433972

Tighten the 2 bolts. [*2]

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


f.
C431679

Using a torque wrench, measure the turning torque of the steering main shaft.

Preload:

1.0 to 2.2 N*m (11 to 22 kgf*cm, 9 to 19 in.*lbf)


NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the turning torque is not as specified, loosen the 2 bolts and repeat steps [*1] and [*2] to recenter the axis of the power steering ECU with motor assembly.


g.

Remove the steering wheel assembly set bolt.


h.
C433971

Install the harness bracket to the electric power steering column sub-assembly with the bolt.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


i.
C433970

Engage the clamp.


j.

Connect the connector.


Hide 45020B 3.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

Hide 4.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.INSTALL STEERING COLUMN ASSEMBLY

Hide 45260 6.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45260 7.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 8.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 84340 10.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 55480D 11.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 53601 12.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55317E 13.INSTALL NO. 1 INSTRUMENT SIDE PANEL

Hide 62311B 14.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 55606 15.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62111C 16.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 17.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 58802E 18.INSTALL FRONT CONSOLE BOX SUB-ASSEMBLY

Hide 19.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Hide 45286B 20.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 21.INSTALL LOWER STEERING COLUMN COVER

Hide 22.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 23.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 24.INSTALL STEERING WHEEL ASSEMBLY

Hide 25.CHECK STEERING WHEEL CENTER POINT

Hide 45130 26.INSTALL HORN BUTTON ASSEMBLY

Hide 27.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 29. PERFORM POWER STEERING ECU INITIAL SETTING

Hide 45130 30.INSPECT HORN BUTTON ASSEMBLY

Hide 33. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART