Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087837 M15A-FKS ENGINE MECHANICAL _0424626 CYLINDER HEAD GASKET A

M15A-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 17167 3.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 7.REMOVE THROTTLE BODY GASKET

Hide 23820 8.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY

Hide 12262 9.REMOVE NO. 2 VENTILATION HOSE

Hide 25680 10.REMOVE EGR COOLER ASSEMBLY

Hide 25601 11.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 17177 14.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 15.REMOVE FUEL TUBE SUB-ASSEMBLY

Hide 23902 16.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY

Hide 23802B 17.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 18.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16261G 19.REMOVE WATER BY-PASS HOSE NO.1

Hide 23250 22.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11452D 24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16281 25.REMOVE NO. 4 WATER BY-PASS HOSE

Hide 11102A 26.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 27.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 28.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Hide 15370 29.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

Hide 29300 30.REMOVE VACUUM PUMP ASSEMBLY

Hide 13470 31.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 11201 32.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 33.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 34.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 35.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 36.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 38.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13050 39.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 41.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 42.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 43.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 44.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 45.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 13631 46.REMOVE BALANCESHAFT DRIVE GEAR

Hide 23477 47.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 48.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13501A 50.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 13502B 51.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 11101 52.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 53.REMOVE CYLINDER HEAD GASKET

A466044

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 54.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 55.INSPECT CYLINDER HEAD SUB-ASSEMBLY