Home › Engine / Hybrid System › 1KR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.07
RM36W0E _51 Engine / Hybrid System _091036 1KR-FE INTAKE / EXHAUST _0431304 INTAKE MANIFOLD A

1KR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

a.

Using an E6 "TORX" socket wrench, install the 2 stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17177 2.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 44783 3.INSTALL VACUUM HOSE CLAMP

a.

for LHD:

i.

Engage the clamp to install the vacuum hose clamp to the intake manifold.



b.

for RHD:

i.

Engage the 2 clamps to install the 2 vacuum hose clamps to the intake manifold.



Hide 17111 4.INSTALL INTAKE MANIFOLD

a.

Install the intake manifold to the cylinder head sub-assembly with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Install the fuel hose bracket to the intake manifold with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

Install the wire harness clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Engage the 3 clamps to connect the wire harness to the intake manifold and wire harness clamp bracket.


e.

Connect the connector.


f.

Engage the clamp to connect the fuel tube sub-assembly to the fuel hose clamp.


Hide 25601 5.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 17650G 6.INSTALL PURGE VALVE (PURGE VSV)

Hide 23827A 7.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.

Connect the No. 2 fuel vapor feed hose to the intake manifold and slide the hose clip to secure it.


b.

Engage the 4 clamps to connect the No. 1 water by-pass hose and No. 2 water by-pass hose to the intake manifold.


Hide 8.CONNECT VACUUM HOSE ASSEMBLY

a.

for RHD:

i.

Engage the clamp to connect the vacuum hose assembly to the vacuum hose clamp.



b.

Engage the clamp to connect the vacuum hose assembly to the vacuum hose clamp.


c.

Align the vacuum hose assembly connector with the intake manifold, and push them together until the vacuum hose assembly connector makes a "click" sound.

NOTICE:

After connecting the vacuum hose assembly connector and intake manifold, check that they are securely connected by trying to pull them apart.



Hide 22030 9.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 55701J 10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735A 12.INSTALL WATER GUARD PLATE LH (for LHD)

Hide 55735A 13.INSTALL WATER GUARD PLATE LH (for RHD)

Hide 55815E 14.INSTALL NO. 1 FRONT VENTILATOR SEAL (for LHD)

Hide 55815E 15.INSTALL NO. 1 FRONT VENTILATOR SEAL (for RHD)

Hide 16.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY