Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › CAMSHAFT › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431326 CAMSHAFT A

1KR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 15678A 1.INSTALL OIL CONTROL VALVE FILTER

Hide 13520 2.TEMPORARILY INSTALL CAMSHAFT TIMING SPROCKET ASSEMBLY

a.
A320144C02
1.063,0.844 1.396,0.229 1.396,0.229 1.604,0.229 true 2.469,0.854 2.802,0.24 2.802,0.24 3.01,0.24 true 3.073,0.156 3.385,0.313 0.313,0.156 10 false *a 1.646,0.156 1.958,0.313 0.313,0.156 10 false *b
*a Straight Pin
*b Straight Pin Hole


Fit the camshaft timing sprocket assembly and camshaft together with the straight pin and straight pin hole aligned as shown in the illustration.


b.

Temporarily install the camshaft timing sprocket assembly with the bolt.


c.

Make sure that the camshaft timing sprocket assembly gear is locked.


Hide 13511 3.INSTALL CAMSHAFT

a.
A324343C01
0.885,1.375 0.385,1.115 0.385,1.115 0.875,0.813 true 0.208,1.042 0.521,1.198 0.313,0.156 10 false *a
*a Apply engine oil


Apply engine oil to the cams of each camshaft, the journals of the cylinder head sub-assembly and the top of each valve lifter.


b.
A323252C01
1.427,0.198 1.688,0.375 true 1.688,1.042 1.688,0.583 true 1.25,0.135 1.469,0.292 0.219,0.156 10 false *a 1.594,1.094 1.906,1.25 0.313,0.156 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the timing chain plate with the timing mark of the camshaft timing sprocket assembly and install the chain sub-assembly.


Hide 13512 4.INSTALL NO. 2 CAMSHAFT

a.

Set the No. 2 camshaft onto the cylinder head sub-assembly.


b.
A421775C01
0.302,1.365 0.49,1.365 true 1.292,1.281 1.479,1.281 true 2.094,1.281 2.281,1.281 true 2.875,1.281 3.063,1.281 true 2.885,2.208 3.073,2.208 true 1.271,2.219 1.458,2.219 true 2.083,2.24 2.271,2.24 true 0.063,1.271 0.26,1.469 0.198,0.198 10 true *1 1.552,1.208 1.781,1.406 0.229,0.198 10 true *2 2.302,1.208 2.531,1.406 0.229,0.198 10 true *2 3.094,1.188 3.323,1.385 0.229,0.198 10 true *2 3.135,2.094 3.365,2.292 0.229,0.198 10 true *2 1.531,2.135 1.76,2.333 0.229,0.198 10 true *2 2.302,2.156 2.531,2.354 0.229,0.198 10 true *3 0.198,0.479 0.406,0.698 0.208,0.219 10 true 14 0.083,1.625 0.292,1.844 0.208,0.219 10 true 13 0.208,2.781 0.417,3 0.208,0.219 10 true 15 1.115,2.781 1.344,3 0.229,0.219 10 true 10 1.531,1.771 1.76,1.99 0.229,0.219 10 true 9 1.531,1.573 1.76,1.792 0.229,0.219 10 true 3 1.167,0.51 1.396,0.729 0.229,0.219 10 true 4 1.958,0.531 2.188,0.75 0.229,0.219 10 true 2 2.333,1.563 2.563,1.781 0.229,0.219 10 true 1 2.333,1.781 2.563,2 0.229,0.219 10 true 7 1.969,2.792 2.198,3.01 0.229,0.219 10 true 8 2.708,2.792 2.938,3.01 0.229,0.219 10 true 12 3.115,1.729 3.344,1.948 0.229,0.219 10 true 11 3.135,1.531 3.365,1.75 0.229,0.219 10 true 5 2.74,0.51 2.969,0.729 0.229,0.219 10 true 6
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap


Place the No. 1 camshaft bearing cap, 5 No. 2 camshaft bearing caps and No. 3 camshaft bearing cap and tighten the bolts with the specified torque in the order shown in the illustration.

Torque:
No. 1 Camshaft Bearing Cap : 15 N*m (153 kgf*cm, 11 ft.*lbf)
No. 2 Camshaft Bearing Cap and No. 3 Camshaft Bearing Cap : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Install the No. 1 camshaft bearing cap and 5 No. 2 camshaft bearing caps with the front marks facing the front of the engine.



Hide 13070A 5.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A421778C01
1.708,0.438 2.01,0.219 2.01,0.219 2.167,0.219 true 1.406,1.229 1.563,1.229 1.563,1.229 1.708,0.583 true 2.229,0.156 2.542,0.354 0.313,0.198 10 true *a 1.146,1.125 1.396,1.333 0.25,0.208 10 true *b
*a Paint Mark
*b Timing Mark


Align the paint mark of the chain plate with the timing mark of the camshaft timing exhaust gear assembly and install the chain sub-assembly.


b.

Install the camshaft timing exhaust gear assembly to the No. 2 camshaft with the knock pin aligned with the pin hole.


c.
A421779C01
0.323,1.927 0.323,1.479 0.323,1.479 0.531,1.479 true 0.792,0.229 1.104,0.427 0.313,0.198 10 true *b 2.938,0.104 3.25,0.302 0.313,0.198 10 true *a 1.448,3.01 1.76,3.208 0.313,0.198 10 false *c 2.417,3.052 2.729,3.25 0.313,0.198 10 false *d 0.177,1.969 0.635,2.167 0.458,0.198 10 true SST
*a Hold
*b Turn
*c Torque wrench with a fulcrum length of 260 mm (10.24 in.)
*d SST with a fulcrum length of 100 mm (3.94 in.)


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the bolt using SST.

SST
09249-37010  

Torque:
without SST : 54 N*m (551 kgf*cm, 40 ft.*lbf)
with SST : 39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.).

·

The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.24 in.).

·

If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 13520 6.TIGHTEN CAMSHAFT TIMING SPROCKET ASSEMBLY

a.
A421780C01
0.615,1.49 0.625,1.063 0.625,1.063 1.01,1.063 true 2.875,0.135 3.188,0.333 0.313,0.198 10 true *a 1.531,0.49 1.844,0.688 0.313,0.198 10 true *b 1.396,3.031 1.708,3.229 0.313,0.198 10 false *c 2.427,3.042 2.74,3.24 0.313,0.198 10 false *d 0.458,1.531 0.917,1.729 0.458,0.198 10 true SST
*a Hold
*b Turn
*c Torque wrench with a fulcrum length of 260 mm (10.24 in.)
*d SST with a fulcrum length of 100 mm (3.94 in.)


Using a wrench to hold the hexagonal portion of the camshaft, install the bolt using SST.

SST
09249-37010  

Torque:
without SST : 54 N*m (551 kgf*cm, 40 ft.*lbf)
with SST : 39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.).

·

The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.24 in.).

·

If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 11302R 8.INSTALL TIMING GEAR COVER TIGHT PLUG

a.

Remove the hexagon wrench from the No. 1 chain tensioner assembly.


b.
A201138C21
2.594,1.281 2.115,0.896 false 2.563,1.313 2.74,1.5 0.177,0.188 10 false *a
*a Adhesive 1324


Clean the timing gear cover tight plug and the bolt holes of the timing chain cover sub-assembly and apply adhesive to the threads of the timing gear cover tight plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Using an 8 mm socket hexagon wrench, install the timing gear cover tight plug to the timing chain cover sub-assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 11213 11.INSTALL CYLINDER HEAD COVER GASKET

Hide 11201 12.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11101J 13.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 29603B 14.CONNECT OIL LEVEL GAUGE GUIDE OIL HOSE

a.

Connect the oil hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 15.CONNECT ENGINE WIRE

a.

w/ Differential Pressure Sensor

i.

Connect the differential pressure sensor connector.



b.
A421765

Connect the heated oxygen sensor connector.


c.

Engage the clamp.


d.
A421764

Engage the 2 clamps.


e.
A471143

Install the nut.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


f.

Engage the 5 clamps.


g.

Connect the camshaft position sensor connector and cam timing oil control valve assembly.


Hide 17735 17.INSTALL AIR CLEANER ASSEMBLY WITH DUCT