Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › VALVE CLEARANCE › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431325 VALVE CLEARANCE N

1KR-FE ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


PROCEDURE

Hide 1.REMOVE AIR CLEANER ASSEMBLY WITH DUCT

Hide 29603B 4.DISCONNECT OIL LEVEL GAUGE GUIDE OIL HOSE

Hide 11101E 5.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11101J 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11201 7.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 8.REMOVE CYLINDER HEAD COVER GASKET

Hide 9.SET NO. 1 CYLINDER TO TDC/EXHAUST

Hide 10.INSPECT VALVE CLEARANCE

a.
A421760C01
1.74,0.625 1.885,0.292 1.885,0.292 2.01,0.615 false 2.313,1.552 2.458,2 2.458,2 2.583,1.542 false 1.781,0.083 2.094,0.281 0.313,0.198 10 false *a 2.385,2 2.688,2.177 0.302,0.177 10 false *b
*a Intake Side
*b Exhaust Side


Check only the valves indicated.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Valve Clearance (Cold):
Intake Side:

0.145 to 0.235 mm (0.00571 to 0.00925 in.)

Exhaust Side:

0.275 to 0.365 mm (0.01083 to 0.01437 in.)


HINT:

Insert the feeler gauge from the spark plug side (center).



ii.

Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.



b.

Turn the crankshaft 1 revolution (360°).


c.
A421761C01
1.198,0.573 1.875,0.219 1.875,0.219 2.563,0.615 true 1.417,0.573 1.875,0.229 1.875,0.229 2.333,0.615 false 1.427,1.604 1.521,1.917 1.521,1.917 1.74,1.552 false 1.188,1.625 1.521,1.917 1.521,1.917 2,1.552 false 1.792,0.031 2.104,0.229 0.313,0.198 10 false *a 1.448,1.938 1.76,2.135 0.313,0.198 10 false *b
*a Intake Side
*b Exhaust Side


Check only the valves indicated.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Valve Clearance (Cold):
Intake Side:

0.145 to 0.235 mm (0.00571 to 0.00925 in.)

Exhaust Side:

0.275 to 0.365 mm (0.01083 to 0.01437 in.)


HINT:

Insert the feeler gauge from the spark plug side (center).



ii.

Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.



Hide 11.ADJUST VALVE CLEARANCE

a.

Remove the camshaft and No. 2 camshaft.

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL



c.
A001082

Using a micrometer, measure the thickness of the removed valve lifters.


d.

Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

A Thickness of new lifter
B Thickness of used lifter
C Measured valve clearance

Valve Clearance:

Intake A = B + (C - 0.18 mm (0.00709 in.))

Exhaust A = B + (C - 0.31 mm (0.0122 in.))


HINT:
·

Select a new lifter with a thickness as close to the calculated values as possible.

·

Lifters are available in 29 sizes in increments of 0.020 mm (0.0008 in.), from 5.12 mm (0.2016 in.) to 5.68 mm (0.2236 in.).

·

Refer to the following Valve Lifter Selection Charts.





f.

Install the camshaft and No. 2 camshaft.

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION

A105103E04
2.073,0.823 5.125,1.344 3.052,0.521 10 false Valve Lifter Selection Chart (Intake) 5.313,1.125 6.031,1.74 0.719,0.615 10 false Measured Clearance mm (in.) 5.885,1.729 6.552,2.427 0.667,0.698 10 false Installed Lifter Thickness mm (in.)

A105104E04
2.26,0.844 4.99,1.365 2.729,0.521 10 false Valve Lifter Selection Chart (Exhaust) 5.667,1.135 6.385,1.802 0.719,0.667 10 false Measured Clearance mm (in.) 6.219,1.74 6.896,2.479 0.677,0.74 10 false Installed Lifter Thickness mm (in.)

HINT:
New Lifter Thickness mm (in.)
Lifter No. Thickness Lifter No. Thickness Lifter No. Thickness
12 5.12 (0.2016) 32 5.32 (0.2094) 52 5.52 (0.2173)
14 5.14 (0.2024) 34 5.34 (0.2102) 54 5.54 (0.2181)
16 5.16 (0.2031) 36 5.36 (0.2110) 56 5.56 (0.2189)
18 5.18 (0.2039) 38 5.38 (0.2118) 58 5.58 (0.2197)
20 5.20 (0.2047) 40 5.40 (0.2126) 60 5.60 (0.2205)
22 5.22 (0.2055) 42 5.42 (0.2134) 62 5.62 (0.2213)
24 5.24 (0.2063) 44 5.44 (0.2142) 64 5.64 (0.2220)
26 5.26 (0.2071) 46 5.46 (0.2150) 66 5.66 (0.2228)
28 5.28 (0.2079) 48 5.48 (0.2157) 68 5.68 (0.2236)
30 5.30 (0.2087) 50 5.50 (0.2165) - -



Hide 11213 12.INSTALL CYLINDER HEAD COVER GASKET

Hide 11201 13.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11101J 14.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 29603B 15.CONNECT OIL LEVEL GAUGE GUIDE OIL HOSE

Hide 18.INSTALL AIR CLEANER ASSEMBLY WITH DUCT