Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P036511  Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground  P036515  Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open  P036531  Camshaft Position Sensor "B" Bank 1 No Signal  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE (Magnet Resistance Element).

The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P036511 Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground Camshaft position sensor (for exhaust camshaft) output stays low (1 trip detection logic).
·

Short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

ECM


Comes on DTC stored Engine A
P036515 Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open Camshaft position sensor (for exhaust camshaft) output stays high (1 trip detection logic).
·

Open in camshaft position sensor (for exhaust camshaft) circuit

·

Short in power source circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

ECM


Comes on DTC stored Engine A
P036531 Camshaft Position Sensor "B" Bank 1 No Signal Teeth of camshaft timing rotor or camshaft position (for exhaust camshaft) cannot be detected correctly for 5 crankshaft revolutions (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

These DTCs are detected when the engine is running or the engine cranks 100 revolutions or more.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If any DTCs related to the manifold absolute pressure sensor, accelerator pedal sensor assembly and camshaft position sensor are output simultaneously, inspect the VC circuit of each component.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

Pre-procedure1

a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D10-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)

Pre-procedure1

a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D10-1 (VVE-) - D50-81 (EV-) Always Below 1 Ω
D10-2 (VVE+) - D50-80 (EV+) Always Below 1 Ω
D10-1 (VVE-) or D50-81 (EV-) - Body ground Always 10 kΩ or higher
D10-2 (VVE+) or D50-80 (EV+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.CHECK CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) INSTALLATION
a.

Check the camshaft position sensor (for exhaust camshaft) installation condition.

OK:

Camshaft position sensor (for exhaust camshaft) is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT EXHAUST CAMSHAFT

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

4.INSPECT EXHAUST CAMSHAFT
a.

Inspect the teeth of the exhaust camshaft.

OK:

The teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NG

5.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515 OR P036531)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515 OR P036531)

Pre-procedure1

a.

Start the engine.


b.

Stop the engine and wait for at least 10 seconds.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P036511, P036515 or P036531 is output B



Post-procedure1

d.

None.



A

END

B

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)

Pre-procedure1

a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D10-3 (VC2) - D50-112 (VCE1) Always Below 1 Ω
D10-3 (VC2) or D50-112 (VCE1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR