Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM J

1KR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The Fuel injectors are installed in the intake port, and inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Disconnect the fuel injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F5-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F6-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F7-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F8-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F9-1 (#10) - Body ground Ignition switch ON 11 to 14 V


HINT:

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.



Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - FUEL INJECTOR ASSEMBLY)
2.INSPECT FUEL INJECTOR ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (#1) - D50-102 (#1) Always Below 1 Ω
F7-2 (#4) - D50-131 (#4) Always Below 1 Ω
F5-2 (#2) - D50-133 (#2) Always Below 1 Ω
F8-2 (#5) - D50-100 (#5) Always Below 1 Ω
F6-2 (#3) - D50-101 (#3) Always Below 1 Ω
F9-2 (#6) - D50-132 (#6) Always Below 1 Ω
F4-2 (#1) or D50-102 (#1) - Body ground Always 10 kΩ or higher
F7-2 (#4) or D50-131 (#4) - Body ground Always 10 kΩ or higher
F5-2 (#2) or D50-133 (#2) - Body ground Always 10 kΩ or higher
F8-2 (#5) or D50-100 (#5) - Body ground Always 10 kΩ or higher
F6-2 (#3) or D50-101 (#3) - Body ground Always 10 kΩ or higher
F9-2 (#6) or D50-132 (#6) - Body ground Always 10 kΩ or higher


HINT:
·

According to the connection condition of the vehicle wire harness connector that connects to the fuel injector assembly, check that there is continuity between either of the terminal pairs.

·

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - FUEL INJECTOR ASSEMBLY)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the fuel injector assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - F4-1 (#10) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - F7-1 (#10) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - F5-1 (#10) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - F8-1 (#10) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - F6-1 (#10) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - F9-1 (#10) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) or F4-1 (#10) - Body ground Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay) or F7-1 (#10) - Body ground Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay) or F5-1 (#10) - Body ground Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay) or F8-1 (#10) - Body ground Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay) or F6-1 (#10) - Body ground Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay) or F9-1 (#10) - Body ground Always 10 kΩ or higher


HINT:

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR