Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P013000  O2 (A/F) Sensor Circuit Slow Response Bank 1 Sensor 1  


DESCRIPTION

Refer to DTC P013013.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P013013

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P013000 O2 (A/F) Sensor Circuit Slow Response Bank 1 Sensor 1 When vehicle is being driven at a constant speed of 75 km/h (47 mph) sensor response is slow (RICH-LEAN cycle takes 3 seconds or more) 5 times (malfunction detection takes approximately 30 seconds or more) (3 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

Fuel pressure

·

Fuel injector assembly

·

Gas leakage from exhaust system


Comes on DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

HINT:

RICH-LEAN cycle

A319418E02
0.271,1.969 1.74,2.333 1.469,0.365 10 false Heated Oxygen Sensor (Sensor 1) Voltage 2.344,3.323 3.719,3.552 1.375,0.229 10 false Lean Side Frequency 3.531,0.677 4.906,0.906 1.375,0.229 10 false Rich Side Frequency 3.25,0.292 4.135,0.594 0.885,0.302 10 false One Cycle 5.438,2.021 5.948,2.323 0.51,0.302 10 false 0.45 V


WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Drive the vehicle at an average vehicle speed of approximately 50 to 60 km/h (31 to 37 mph) in an urban area for approximately 30 minutes.

CAUTION / NOTICE / HINT

HINT:
·

A high heated oxygen sensor voltage (0.55 V or more) could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A low heated oxygen sensor voltage (0.4 V or less) could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P013000)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P013000 is output A
P013000 and other DTCs are output B


HINT:

If any DTCs other than P013000 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Warm up the engine at an engine speed of 2500 rpm for approximately 3 minutes.


Procedure1

b.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Injection Volume
O2 Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 277,1305,218

c.

Monitor the voltage output of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) (O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
The heated oxygen sensor reacts in accordance with increases and decreases of the fuel injection volume:
+12.5% = Rich output:

Higher than 0.55 V

-12.5% = Lean output:

Below 0.4 V


A318963E03
0.135,0.417 0.75,0.615 0.615,0.198 10 false Case 0.74,0.333 2.375,0.833 1.635,0.5 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 2.729,0.333 4.583,0.865 1.854,0.531 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.042,0.417 6.938,0.917 1.896,0.5 10 false Main Suspected Trouble Area 0.615,1 2.083,1.323 1.469,0.323 10 false Injection Volume 0.854,1.281 2.323,1.604 1.469,0.323 8 false +12.5% 0.865,1.531 2.333,1.854 1.469,0.323 8 false -12.5% 0.615,2 2.083,2.323 1.469,0.323 10 false Output Voltage 0.729,2.271 1.333,2.656 0.604,0.385 8 false Higher than 0.55 V 0.688,2.573 2.156,2.896 1.469,0.323 8 false Below 0.4 V 2.115,2.458 2.615,2.844 0.5,0.385 10 false OK 2.615,1 4.083,1.323 1.469,0.323 10 false Injection Volume 3.01,1.313 4.479,1.635 1.469,0.323 8 false +12.5% 3.021,1.531 4.49,1.854 1.469,0.323 8 false -12.5% 5.875,1.938 6.031,2.135 0.156,0.198 10 false - 4.885,3.927 7.031,4.302 2.146,0.375 10 false - Heated oxygen sensor (sensor 1) 4.917,5.167 6.969,5.635 2.052,0.469 10 false - Extremely rich or lean actual air fuel ratio 4.917,5.583 6.854,5.99 1.938,0.406 10 false - Fuel injector assembly leak or blockage 4.917,6 7.052,6.406 2.135,0.406 10 false - Gas leak from exhaust system 4.917,6.26 7.052,6.667 2.135,0.406 10 false - Ignition system 4.917,6.521 7.052,6.927 2.135,0.406 10 false - Fuel pressure 4.917,6.781 6.677,7.271 1.76,0.49 10 false - Manifold absolute pressure sensor 4.917,7.177 6.719,7.729 1.802,0.552 10 false - Engine coolant temperature sensor 0.667,3.083 2.135,3.406 1.469,0.323 10 false Injection Volume 0.802,3.333 2.271,3.656 1.469,0.323 8 false +12.5% 0.823,3.594 2.292,3.917 1.469,0.323 8 false -12.5% 0.698,4 2.167,4.323 1.469,0.323 10 false Output Voltage 0.76,4.521 1.292,4.875 0.531,0.354 8 false Almost no reaction 2.135,4.531 3.604,4.854 1.469,0.323 10 false NG 2.615,3.083 4.083,3.406 1.469,0.323 10 false Injection Volume 3.021,3.333 4.49,3.656 1.469,0.323 8 false +12.5% 3.042,3.594 4.51,3.917 1.469,0.323 8 false -12.5% 2.667,4.01 4.135,4.333 1.469,0.323 10 false Output Voltage 2.635,4.406 3.854,4.771 1.219,0.365 8 false Higher than 0.55 V 2.958,4.656 4.427,4.979 1.469,0.323 8 false Below 0.4 V 4.281,4.521 5.75,4.844 1.469,0.323 10 false OK 0.667,5.167 2.135,5.49 1.469,0.323 10 false Injection Volume 0.896,5.688 2.365,6.01 1.469,0.323 8 false +12.5% 0.896,5.948 2.365,6.271 1.469,0.323 8 false -12.5% 0.667,6.417 2.135,6.74 1.469,0.323 10 false Output Voltage 0.813,6.854 1.344,7.24 0.531,0.385 8 false Almost no reaction 2.115,6.906 3.583,7.229 1.469,0.323 10 false NG 4.375,6.885 5.844,7.208 1.469,0.323 10 false NG 2.667,6.427 4.135,6.75 1.469,0.323 10 false Output Voltage 2.667,6.885 3.833,7.167 1.167,0.281 8 false Almost no reaction 2.667,5.177 4.135,5.5 1.469,0.323 10 false Injection Volume 3.115,5.688 4.583,6.01 1.469,0.323 8 false +12.5% 3.125,5.969 4.594,6.292 1.469,0.323 8 false -12.5% 2.615,2 4.083,2.323 1.469,0.323 10 false Output Voltage 2.656,2.313 3.99,2.604 1.333,0.292 8 false Higher than 0.55 V 2.958,2.542 4.427,2.865 1.469,0.323 8 false Below 0.4 V 4.354,2.427 4.854,2.813 0.5,0.385 10 false OK 0.26,1.896 0.875,2.094 0.615,0.198 10 false 1 0.26,3.906 0.875,4.104 0.615,0.198 10 false 2 0.25,6.188 0.865,6.385 0.615,0.198 10 false 3

The following procedure enables the technician to check and graph the voltage outputs of both the heated oxygen sensors.

To display the graph, enter the following menus:

Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2; then press the view button.

HINT:

If the vehicle is short of fuel, the air fuel ratio becomes lean and the heated oxygen sensor DTCs are recorded, and then the MIL illuminates.


Result:
Result Proceed to
Case 2 A
Case 3 B
Case 1 C



Post-procedure1

d.

None.



A

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

B

7.CHECK WHETHER MISFIRE OCCURS

C

10.CLEAR DTC
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D38-4 (OX1A) - D50-126 (OX1A) Always Below 1 Ω
D38-2 (HT1A) - D50-25 (HT1A) Always Below 1 Ω
D38-3 (E1) - D50-125 (E11) Always Below 1 Ω
D38-4 (OX1A) or D50-126 (OX1A) - Body ground Always 10 kΩ or higher
D38-2 (HT1A) or D50-25 (HT1A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013000)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013000)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
P013000 is output B


Post-procedure1

d.

None.



A

END

B

7.CHECK WHETHER MISFIRE OCCURS
7.CHECK WHETHER MISFIRE OCCURS
a.

Check the idling condition.

OK:

Rough idling does not occur.



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE

NG

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE FUEL SYSTEM

9.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

OK

CHECK FOR EXHAUST GAS LEAK

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P013000)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P013000)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTC P013000 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B