Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P030000  Random Misfire Detected  P030100  Cylinder 1 Misfire Detected  P030200  Cylinder 2 Misfire Detected  P030300  Cylinder 3 Misfire Detected  


DESCRIPTION

When a misfire occurs in the engine, hydrocarbons (HC) enter the exhaust gas in high concentrations. If this HC concentration is high enough, there could be an increase in exhaust emission levels. High concentrations of HC can also cause the temperature of the Three-Way Catalytic Converter (TWC) to increase, possibly damaging the TWC. To prevent this increase in emissions and limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. The misfire counter increments when the crankshaft rotation speed variations exceed the threshold values.

If the misfiring rate exceeds the threshold and could cause emission deterioration, the ECM illuminates the MIL.

HINT:
·

The ECM monitors misfires, which could cause emission deterioration, every 1000 crankshaft revolutions. When emission deterioration misfires are detected, the ECM illuminates the MIL and stores a DTC.

·

The ECM monitors misfires, which could damage the TWC, every 200 crankshaft revolutions. If TWC damaging misfires are detected, the ECM flashes the MIL and stores a DTC (2 trip detection logic).



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P030000 Random Misfire Detected Misfiring of random cylinders is detected (2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake manifold

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B
P030100 Cylinder 1 Misfire Detected Misfiring of each cylinder is detected (2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake manifold

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B
P030200 Cylinder 2 Misfire Detected Misfiring of each cylinder is detected (2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake manifold

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B
P030300 Cylinder 3 Misfire Detected Misfiring of each cylinder is detected (2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake manifold

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

HINT:

These DTCs are detected when the engine idles for approximately 10 minutes after warm-up. (Misfire can be clearly checked by activating the air conditioning system.)


WIRING DIAGRAM

Refer to DTC P020111 for fuel injector circuit.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P020111

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record DTCs and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

6.

Read the misfire counts of each cylinder (Misfire Count Cylinder #1 to Misfire Count Cylinder #3) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.

7.

Drive the vehicle several times with the conditions, such as engine speed and engine load, shown in Misfire RPM in the freeze frame data.

HINT:

In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below, with the engine speed and engine load the same as Misfire RPM in the freeze frame data.

Engine Speed (rpm) Duration
Idling 10 minutes or more
1000 4 minutes 30 seconds or more
2000 2 minutes 30 seconds or more
3000 1 minute 30 seconds or more


8.

Check whether misfires have occurred by checking for DTCs and freeze frame data.

9.

Record the DTC(s), freeze frame data and misfire counts.

10.

Turn the ignition switch off and wait for at least 30 seconds.

11.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:

(a)

The fuel level is low.

(b)

Improper fuel is used.

(c)

The spark plugs are dirty.

(d)

The problem is complex and involves multiple factors.


·

After finishing repairs, check that no misfire occurs in each cylinder (Misfire Count Cylinder #1 to Misfire Count Cylinder #3).

·

Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after the repairs.

·

When either Short FT B1S1 or Long FT B1S1 in the freeze frame data is outside the range of +/-25%, the air fuel ratio may be rich (-25% or less) or lean (+25% or more).

·

When the Coolant Temperature in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P030000, P030100, P030200 or P030300 is output A
P030000, P030100, P030200 or P030300 and other DTCs are output B


HINT:

If any DTCs other than P030000, P030100, P030200 and P030300 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

GO TO DTC CHART

2.CHECK PCV HOSE CONNECTIONS
HINT:

Click hereEngine / Hybrid System>1KR-FE (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION


OK:

PCV valve and hose are correctly connected and are not damaged.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE COUNT CYLINDER)

NG

REPAIR OR REPLACE PCV HOSE

3.READ VALUE USING GTS (MISFIRE COUNT CYLINDER)

Pre-procedure1

a.

Start the engine and allow the engine to idle.


Procedure1

b.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
50003 372 1223,1224,1225

Perform the following inspection when misfires cannot be checked using the Data List.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


i.

Considering the freeze frame data, drive the vehicle to reproduce the vehicle conditions present when the misfire occurred.


ii.

Read the Misfire Count Cylinder #1 to Misfire Count Cylinder #3 or DTCs displayed on the GTS.

HINT:
·

Check the [Coolant Temperature], [Engine Run Time], etc. recorded in the freeze frame data to determine the vehicle conditions in which misfires easily occur.

·

If items cannot be confirmed on the Data List after performing the above, determine whether the misfires are concentrated in one cylinder or multiple cylinders using the output DTCs confirmed in step 1.

·

If the misfires are concentrated in one cylinder, proceed to A. If the misfires are concentrated in multiple cylinders, proceed to B.

·

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.





Result:
Result Proceed to
Misfires concentrated in a specific cylinder A
Misfires concentrated in multiple cylinders B


Post-procedure1

c.

None.



A

4.INSPECT SPARK PLUG

B

17.CHECK INTAKE SYSTEM
4.INSPECT SPARK PLUG

OK

5.CHECK FOR SPARKS (SPARK TEST)

NG

5.CHECK FOR SPARKS (SPARK TEST)

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

If the result of the spark test is normal, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

6.CHECK CYLINDER COMPRESSION PRESSURE
6.CHECK CYLINDER COMPRESSION PRESSURE

OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the fuel injector assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F5-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F6-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F7-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F8-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F9-1 (#10) - Body ground Ignition switch ON 11 to 14 V


HINT:

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

8.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the fuel injector assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (#1) - D50-102 (#1) Always Below 1 Ω
F7-2 (#4) - D50-131 (#4) Always Below 1 Ω
F5-2(#2) - D50-133 (#2) Always Below 1 Ω
F8-2(#5) - D50-100 (#5) Always Below 1 Ω
F6-2 (#3) - D50-101 (#3) Always Below 1 Ω
F9-2 (#6) - D50-132 (#6) Always Below 1 Ω
F4-2 (#1) or D50-102 (#1) - Body ground Always 10 kΩ or higher
F7-2 (#4) or D50-131 (#4) - Body ground Always 10 kΩ or higher
F5-2 (#2) or D50-133 (#2) - Body ground Always 10 kΩ or higher
F8-2 (#5) or D50-100 (#5) - Body ground Always 10 kΩ or higher
F6-2 (#3) or D50-101 (#3) - Body ground Always 10 kΩ or higher
F9-2 (#6) or D50-132 (#6) - Body ground Always 10 kΩ or higher


HINT:
·

According to the connection condition of the vehicle wire harness connector that connects to the fuel injector assembly, check that there is continuity between either of the terminal pairs.

·

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.




Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>1KR-FE (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1KR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.



Result:
Proceed to
OK
NG



OK

11.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

11.CHECK FUEL PRESSURE

OK

12.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER

12.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D21-3 (VC) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V
D21-1 (PIM) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

14.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Read the values displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385
OK:

Equivalent to atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa (abs) [758 mmHg (abs)].

·

For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.




Result:
Proceed to
OK
NG



OK

15.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER

NG

15.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER

OK

16.CHECK VALVE TIMING

NG

16.CHECK VALVE TIMING
HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


OK:

The match marks of the crankshaft pulley and camshaft pulley align.


Result:
Proceed to
OK
NG



OK

NG

30.CHECK ENGINE MECHANICAL SYSTEM
17.CHECK INTAKE SYSTEM

Click hereEngine / Hybrid System>1KR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


Result:
Proceed to
OK
NG



OK

18.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

18.CHECK FUEL PRESSURE

OK

19.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER

19.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D21-3 (VC) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V
D21-1 (PIM) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

21.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Read the values displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385
OK:

Equivalent to atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa (abs) [758 mmHg (abs)].

·

For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.




Result:
Proceed to
OK
NG



OK

22.INSPECT SPARK PLUG

NG

22.INSPECT SPARK PLUG

OK

23.CHECK FOR SPARKS (SPARK TEST)

NG

23.CHECK FOR SPARKS (SPARK TEST)

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

If the result of the spark test is normal, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

24.CHECK CYLINDER COMPRESSION PRESSURE
24.CHECK CYLINDER COMPRESSION PRESSURE

OK

25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

25.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the fuel injector assembly connectors.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F5-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F6-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F7-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F8-1 (#10) - Body ground Ignition switch ON 11 to 14 V
F9-1 (#10) - Body ground Ignition switch ON 11 to 14 V


HINT:

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

26.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

26.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the fuel injector assembly connectors.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-2 (#1) - D50-102 (#1) Always Below 1 Ω
F7-2 (#4) - D50-131 (#4) Always Below 1 Ω
F5-2 (#2) - D50-133 (#2) Always Below 1 Ω
F8-2 (#5) - D50-100 (#5) Always Below 1 Ω
F6-2 (#3) - D50-101 (#3) Always Below 1 Ω
F9-2 (#6) - D50-132 (#6) Always Below 1 Ω
F4-2 (#1) or D50-102 (#1) - Body ground Always 10 kΩ or higher
F7-2 (#4) or D50-131 (#4) - Body ground Always 10 kΩ or higher
F5-2 (#2) or D50-133 (#2) - Body ground Always 10 kΩ or higher
F8-2 (#5) or D50-100 (#5) - Body ground Always 10 kΩ or higher
F6-2 (#3) or D50-101 (#3) - Body ground Always 10 kΩ or higher
F9-2 (#6) or D50-132 (#6) - Body ground Always 10 kΩ or higher


HINT:
·

According to the connection condition of the vehicle wire harness connector that connects to the fuel injector assembly, check that there is continuity between either of the terminal pairs.

·

The vehicle wire harness connector that connects to the fuel injector assembly can be connected to either of the 2 fuel injector assemblies of the same cylinder.




Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

27.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>1KR-FE (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

28.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER

NG

REPLACE FUEL INJECTOR ASSEMBLY

28.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER

OK

29.CHECK VALVE TIMING

NG

29.CHECK VALVE TIMING
a.

Check for looseness or jumped tooth in the timing chain.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


OK:

The match marks of the crankshaft pulley and camshaft pulley align.



Result:
Proceed to
OK
NG



OK

NG

30.CHECK ENGINE MECHANICAL SYSTEM
30.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

31.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

31.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTC)
32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTC)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P030000, P030100, P030200 or P030300 is output A
DTCs are not output B



Post-procedure1

d.

None.



A

B

END