Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › from 2020.07
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432170 TRANSMISSION CONTROL CABLE A

C551 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 57543C 9.REMOVE CENTER NO. 1 FLOOR BRACE (w/ Brace)

Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58166A 11.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 12.REMOVE FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 58153 13.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

Hide 58910C 14.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 15.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C433395

Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.


b.
C433396

Disconnect the transmission control shift cable from the floor shift shift lever assembly.


c.
C433397

Disengage the 2 claws to disconnect the transmission control cable assembly from the floor shift shift lever assembly.

NOTICE:

Do not forcibly pull the transmission control cable assembly into the cabin.



d.
C433398N01
2.094,1.854 2.25,2.042 0.156,0.188 10 true A 2.635,1.104 2.792,1.292 0.156,0.188 10 true A 0.802,0.563 0.958,0.75 0.156,0.188 10 true B 2.01,0.229 2.167,0.417 0.156,0.188 10 true B

Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.


e.

Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.


f.
C440589

Remove the nut.


g.

Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.


h.
C435413

Remove the 2 nuts and transmission control cable assembly from the vehicle body.