Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422065 TRANSMISSION CONTROL CABLE A

K320 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the shift lever is in N.


a.
C432801C01
0.323,1.448 0.542,1.656 0.219,0.208 10 true *a
*a N


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



b.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Engage the guide to connect the transmission control cable assembly to vehicle body.


d.

Install the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


e.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


f.
C429234C03
0.771,2.188 1.083,2.344 0.313,0.156 10 false *a 2.167,2.198 2.479,2.354 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.


g.
C400603C07
1.854,1.74 1.531,1.198 false 2.583,1.677 2.167,0.979 false 2.615,1.698 2.927,1.854 0.313,0.156 10 false *1 1.875,1.771 2.188,1.927 0.313,0.156 10 false *2
*1 Adjuster Case
*2 Adjuster Case Cover


Slide the adjuster case cover in the direction shown by the arrow.


h.
C400817C06
2.156,1.635 1.896,1.177 false 2.646,1.594 2.313,1.031 false 2.635,1.583 2.948,1.74 0.313,0.156 10 false *1 2.156,1.646 2.469,1.802 0.313,0.156 10 false *2
*1 Adjuster Case
*2 Lock Piece


Using a precision screwdriver, pull out the lock piece of the adjuster case.


i.
C400818C03
0.448,1.208 0.625,1.208 0.625,1.208 1.729,1.49 true 2.188,1.26 2.896,2.208 2.896,2.208 2.208,3.479 true 0.26,1.115 0.573,1.271 0.313,0.156 10 false *1 2.01,0.365 2.323,0.521 0.313,0.156 10 false *a 2.948,2.104 3.26,2.26 0.313,0.156 10 false *2
*1 Lock Nut
*2 Stopper
*a Push in


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


j.
C435107C01
0.771,1.104 0.531,0.979 false 2.604,1.021 2.365,0.896 false 0.344,0.896 0.656,1.052 0.313,0.156 10 false *1 2.208,0.813 2.521,0.969 0.313,0.156 10 false *1
*1 Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

After installation, check that the outer part of the stopper is as shown in the illustration.

·

Do not forcibly pull the transmission control cable assembly into the cabin.




k.
C435108

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.

·

Before connecting the floor shift transmission control select cable, check that the shift lever is in N.




l.
C435105C01
1.854,0.656 2.25,0.99 true 2.75,1.323 2.531,1.052 true 1.646,0.563 1.844,0.75 0.198,0.188 10 true *2 2.688,1.354 2.917,1.542 0.229,0.188 10 true *1
*1 Lock Piece
*2 Adjuster Case


Push in the lock piece of the adjuster case to lock it.

NOTICE:
C414647C05
1.271,0.333 1.604,0.333 false 2.333,1.667 2.583,1.167 2.583,1.167 2.75,1.167 true 2.781,1.063 3.094,1.219 0.313,0.156 10 false *1 1.646,0.24 1.958,0.396 0.313,0.156 10 false *2
*1 Transmission Control Cable Assembly
*2 Lever Shaft


·

When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

·

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.




m.
C435106C01
2.844,1.302 2.573,1.052 true 2.354,1.396 2.354,1.094 true 2.771,1.323 3.021,1.49 0.25,0.167 10 true *1 2.281,1.427 2.531,1.594 0.25,0.167 10 true *2
*1 Adjuster Case
*2 Adjuster Case Cover


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.



Hide 2.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 58153 3.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR (for TMMF Made)

a.

Install the front No. 2 floor heat insulator to the vehicle body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58153 4.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR (for TMC Made)

a.

Install the front No. 2 floor heat insulator to the vehicle body with the 4 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58151 5.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57543C 7.INSTALL CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Hide 51447D 8.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)

Hide 51447D 9.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

Hide 58166A 10.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 11.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 74404A 12.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 17701 14.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 15.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 16.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 17.INSPECT SHIFT LEVER POSITION (for TMMF Made)

Hide 18.INSPECT SHIFT LEVER POSITION (for TMC Made)

Hide 21. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART