Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  P057111  Brake Switch "A" Circuit Short to Ground  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

When the brake pedal is depressed and no signal is received from the stop light switch assembly, this DTC is output.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057111 Brake Switch "A" Circuit Short to Ground Either of the following is detected when the vehicle speed of 3 km/h (2 mph) or more:
1.

With the stop light switch assembly off, the stop light switch assembly is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch assembly off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C439628E04
1.771,6.677 3.531,6.938 1.76,0.26 10 false Stop Light Switch Assembly 4.865,6.521 5.323,6.719 0.458,0.198 10 false A37 4.729,4.021 5.042,4.219 0.313,0.198 10 false 2 4.917,4.156 5.375,4.354 0.458,0.198 10 false STP 4.917,5.063 5.375,5.26 0.458,0.198 10 false STPO 4.917,6.052 5.375,6.25 0.458,0.198 10 false STP2 4.667,4.927 4.979,5.125 0.313,0.198 10 false 28 4.677,5.927 4.99,6.125 0.313,0.198 10 false 12 3.344,5.927 3.656,6.125 0.313,0.198 10 false 1 3.344,4.927 3.656,5.125 0.313,0.198 10 false 4 3.344,4.021 3.656,4.219 0.313,0.198 10 false 3 2.958,6.042 3.417,6.24 0.458,0.198 10 false OUT 2.958,5.052 3.417,5.25 0.458,0.198 10 false ACC 3.135,4.146 3.594,4.344 0.458,0.198 10 false L 1.844,4.135 2.302,4.333 0.458,0.198 10 false B 1.833,6.042 2.292,6.24 0.458,0.198 10 false GND 0.969,4.313 1.427,4.51 0.458,0.198 10 false STOP 0.781,3.292 2.208,3.469 1.427,0.177 10 false from Auxiliary Battery 2.125,7.292 3.365,7.573 1.24,0.281 10 false to Stop Light Circuit 1.635,5.938 1.948,6.135 0.313,0.198 10 false 2 1.604,4.021 1.917,4.219 0.313,0.198 10 false 7 1.792,6.521 2.25,6.719 0.458,0.198 10 false A63 4.844,6.708 6.385,7.094 1.542,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 1.958,2.76 2.323,2.969 0.365,0.208 10 false ECM 1.198,1.354 3.323,1.76 2.125,0.406 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly)*5 4.917,2.906 6.729,3.323 1.813,0.417 10 false Certification ECU (Smart Key ECU Assembly)*1 *5 2.708,0.896 3.167,1.094 0.458,0.198 10 false H20 5.271,0.896 5.729,1.094 0.458,0.198 10 false STP 2.271,0.885 2.729,1.083 0.458,0.198 10 false STP 5.26,2.344 5.719,2.542 0.458,0.198 10 false STP1 4.99,2.208 5.302,2.406 0.313,0.198 10 false 21 2.781,0.677 3.125,0.938 0.344,0.26 10 false 4 0.417,7.729 3.333,8.063 2.917,0.333 10 false *1: w/ Entry and Start System 3.552,7.75 6.823,8.135 3.271,0.385 10 false *2: w/o Entry and Start System 3.198,0.667 3.542,0.927 0.344,0.26 10 false 8 3.135,0.896 3.594,1.094 0.458,0.198 10 false H19 2.719,1.135 3.063,1.396 0.344,0.26 10 false *1 3.177,1.135 3.521,1.396 0.344,0.26 10 false *2 3.156,2.115 3.531,2.354 0.375,0.24 10 false 21 5.479,1.302 5.854,1.5 0.375,0.198 10 false D71 5.479,1.469 6.281,1.698 0.802,0.229 10 false TCM*5 5.01,0.781 5.354,1.042 0.344,0.26 10 false 43 2.292,2.333 2.75,2.531 0.458,0.198 10 false STP 3.115,2.354 3.448,2.521 0.333,0.167 10 false A54 4.906,2.76 5.365,2.958 0.458,0.198 10 false H45 2.667,2.354 2.99,2.542 0.323,0.188 10 false A55 2.74,2.104 3.052,2.302 0.313,0.198 10 false 57 2.708,2.594 3.021,2.792 0.313,0.198 10 false *3 3.146,2.604 3.458,2.802 0.313,0.198 10 false *4 0.417,8.094 1.573,8.281 1.156,0.188 10 false *3: for 1KR-FE 3.552,8.104 4.76,8.302 1.208,0.198 10 false *4: for M15A-FKS 0.406,8.448 1.51,8.656 1.104,0.208 10 false *5: for CVT 1.615,4.927 1.875,5.115 0.26,0.188 10 false 6 1.844,5.063 2,5.26 0.156,0.198 10 false B 0.771,7 2.917,7.198 2.146,0.198 10 false from IGP Relay 0.656,5.208 1.771,5.396 1.115,0.188 10 false ECU-IGP NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle specification.


Result:
Result Proceed to
LHD A
RHD B



A

2.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

B

14.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model LHD)>INSTALLATION

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and stop light switch assembly before inspecting the input signals and other related parts.


Result:
Proceed to
OK
NG



OK

3.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION

3.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STOP LIGHT SW)

NG

10.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.READ VALUE USING GTS (STOP LIGHT SW)
a.

Check that the Stop Light SW display observed on the GTS changes according to brake pedal operation.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Chassis > Brake > Data List
Tester Display
Stop Light SW
50003 435 59
OK:

The GTS displays OFF / ON according to brake pedal operation.



b.

Slowly depress the brake pedal, and check when the stop light switch assembly moves.

OK:

The stop light switch assembly immediately turns on, when the brake pedal is depressed.



c.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

Turn the ignition switch off.


Result:
Result Proceed to
P057111 is not output A
P057111 is output B



A

B

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
8 to 14 V
A37-2 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

Turn the ignition switch off.


Result:
Result Proceed to
P057111 is not output A
P057111 is output B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

10.INSPECT STOP LIGHT SWITCH ASSEMBLY

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
8 to 14 V
A37-2 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

12.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CLEAR DTC

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

Turn the ignition switch off.


Result:
Result Proceed to
P057111 is not output A
P057111 is output B



A

B

14.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model RHD)>INSTALLATION

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and stop light switch assembly before inspecting the input signals and other related parts.


Result:
Proceed to
OK
NG



OK

3.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION