Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C05621C  Brake Pedal Position Sensor Supply Voltage Circuit Voltage Out of Range  C139200  Zero Point Calibration of Stroke Sensor  P057A11  Brake Pedal Position Sensor "A" Circuit Short to Ground  P057A15  Brake Pedal Position Sensor "A" Circuit Short to Battery or Open  P057A28  Brake Pedal Position Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  P057A64  Brake Pedal Position Sensor "A" Signal Plausibility Failure  P05DB11  Brake Pedal Position Sensor "B" Circuit Short to Ground  P05DB15  Brake Pedal Position Sensor "B" Circuit Short to Battery or Open  P05DB28  Brake Pedal Position Sensor "B" Signal Bias Level Out of Range / Zero Adjustment Failure  P05DB64  Brake Pedal Position Sensor "B" Signal Plausibility Failure  P05E064  Brake Pedal Position Sensor "A"/"B" Signal Plausibility Failure  P157A62  Brake Pedal Position Sensor "A" / "B" Brake Master Cylinder Pressure Sensor Multiple Sensor Signal Compare Failure  


DESCRIPTION

The brake pedal stroke sensor sends the brake pedal stroke distance to the skid control ECU inside the brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C05621C Brake Pedal Position Sensor Supply Voltage Circuit Voltage Out of Range Brake pedal stroke sensor assembly power source malfunction detected.
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
C139200 Zero Point Calibration of Stroke Sensor While the brake pedal is not being depressed, brake pedal stroke sensor assembly zero point not calibrated signal is received. (A correct brake pedal stroke sensor assembly zero point learning value is not present).
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P057A11 Brake Pedal Position Sensor "A" Circuit Short to Ground Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 1.
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P057A15 Brake Pedal Position Sensor "A" Circuit Short to Battery or Open Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 1.
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P057A28 Brake Pedal Position Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure Difference in change amount of brake pedal stroke sensor assembly output voltage 1 (SKS1) is abnormally large for 0.1 seconds or more. (SKS1 output comparison invalid).
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P057A64 Brake Pedal Position Sensor "A" Signal Plausibility Failure Difference in change amount of brake pedal stroke sensor assembly output voltage 1 (SKS1) is abnormally large for 0.2 seconds or more. (SKS1 output comparison invalid).
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P05DB11 Brake Pedal Position Sensor "B" Circuit Short to Ground Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 2.
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P05DB15 Brake Pedal Position Sensor "B" Circuit Short to Battery or Open Open or short detected due to abnormality in brake pedal stroke sensor assembly output circuit 2.
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P05DB28 Brake Pedal Position Sensor "B" Signal Bias Level Out of Range / Zero Adjustment Failure Difference in change amount of brake pedal stroke sensor assembly output voltage 2 (SKS2) is abnormally large for 0.1 seconds or more. (SKS2 output comparison invalid).
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P05DB64 Brake Pedal Position Sensor "B" Signal Plausibility Failure Difference in change amount of brake pedal stroke sensor assembly output voltage 2 (SKS2) is abnormally large for 0.2 seconds or more. (SKS2 output comparison invalid).
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P05E064 Brake Pedal Position Sensor "A"/"B" Signal Plausibility Failure Difference between change amounts of brake pedal stroke sensor assembly output voltage 1 (SKS1) and brake pedal stroke sensor assembly output voltage 2 (SKS2) is abnormally large for 0.2 seconds or more. (SKS1 and SKS2 output comparison invalid).
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake
P157A62 Brake Pedal Position Sensor "A" / "B" Brake Master Cylinder Pressure Sensor Multiple Sensor Signal Compare Failure While driving at a vehicle speed of 3 km/h or more, the master cylinder pressure sensor value is too high relative to the brake pedal stroke sensor assembly value for 0.2 seconds or more.
·

Brake pedal stroke sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C443937E03
2.354,1.229 2.813,1.427 0.458,0.198 10 false VSK 4.99,1.094 5.448,1.292 0.458,0.198 10 false 17 2.292,1.854 2.75,2.052 0.458,0.198 10 false SKS1 5.281,1.854 5.74,2.052 0.458,0.198 10 false SKS1 5.292,2.469 5.75,2.667 0.458,0.198 10 false SKS 2.281,2.469 2.74,2.667 0.458,0.198 10 false SKS2 2.344,2.979 2.802,3.177 0.458,0.198 10 false SKG 5.281,2.979 5.74,3.177 0.458,0.198 10 false SKG 0.938,3.573 1.396,3.771 0.458,0.198 10 false A31 0.938,3.75 2.656,4.229 1.719,0.479 10 false Brake Pedal Stroke Sensor Assembly 5.229,3.573 5.688,3.771 0.458,0.198 10 false A39 5.219,3.75 6.76,4.146 1.542,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 5.281,1.229 5.74,1.427 0.458,0.198 10 false VSK 5.042,1.698 5.5,1.896 0.458,0.198 10 false 6 5.01,2.333 5.469,2.531 0.458,0.198 10 false 42 5.01,2.844 5.469,3.042 0.458,0.198 10 false 29 2.781,1.083 3.24,1.281 0.458,0.198 10 false 1 2.792,1.698 3.25,1.896 0.458,0.198 10 false 2 2.792,2.323 3.25,2.521 0.458,0.198 10 false 4 2.792,2.844 3.25,3.042 0.458,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for RHD A
for LHD B



A

2.CHECK BRAKE PEDAL

B

5.CHECK BRAKE PEDAL
2.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model RHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (Brake Actuator Assembly) connector.


c.

Disconnect the A31 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-17 (VSK) - A31-1 (VSK) Always Below 1 Ω
A39-17 (VSK) or A31-1 (VSK) - Body ground Always 10 kΩ or higher
A39-6 (SKS1) - A31-2 (SKS1) Always Below 1 Ω
A39-6 (SKS1) or A31-2 (SKS1) - Body ground Always 10 kΩ or higher
A39-42 (SKS) - A31-4 (SKS2) Always Below 1 Ω
A39-42 (SKS) or A31-4 (SKS2) - Body ground Always 10 kΩ or higher
A39-29 (SKG) - A31-3 (SKG) Always Below 1 Ω
A39-29 (SKG) or A31-3 (SKG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)
a.

Reconnect the A39 skid control ECU (Brake Actuator Assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A31-1 (VSK) - A31-3 (SKG) Ignition switch ON 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model LHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (Brake Actuator Assembly) connector.


c.

Disconnect the A31 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-17 (VSK) - A31-1 (VSK) Always Below 1 Ω
A39-17 (VSK) or A31-1 (VSK) - Body ground Always 10 kΩ or higher
A39-6 (SKS1) - A31-2 (SKS1) Always Below 1 Ω
A39-6 (SKS1) or A31-2 (SKS1) - Body ground Always 10 kΩ or higher
A39-42 (SKS) - A31-4 (SKS2) Always Below 1 Ω
A39-42 (SKS) or A31-4 (SKS2) - Body ground Always 10 kΩ or higher
A39-29 (SKG) - A31-3 (SKG) Always Below 1 Ω
A39-29 (SKG) or A31-3 (SKG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)
a.

Reconnect the A39 skid control ECU (Brake Actuator Assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A31-1 (VSK) - A31-3 (SKG) Ignition switch ON 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)