Refer to DTC P003012.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P003012
Although the DTC titles say oxygen sensor, this DTC relate to the air fuel ratio sensor (sensor 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P2A0026 | O2 Sensor Circuit Range/Performance Bank 1 Sensor 1 Signal Rate of Change Below Threshold | The calculated value for the air fuel ratio sensor (sensor 1) response rate deterioration level is less than the threshold (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
Intake system ·
Fuel injector assembly ·
Fuel pressure (for low pressure) ·
Fuel pressure (for high pressure) ·
Fuel system ·
EGR valve assembly ·
ECM |
Comes on | SAE: P2A00 |
After the engine is warmed up, the ECM performs air fuel ratio feedback control to maintain the air fuel ratio at the stoichiometric level. In addition, active air fuel ratio control is performed for approximately 30 seconds after preconditions are met in order to measure the air fuel ratio sensor (sensor 1) response rate. During active air fuel ratio control, the ECM forcibly increases and decreases the injection volume by a certain amount, based on the stoichiometric air fuel ratio learned during normal air fuel ratio control, and measures the air fuel ratio sensor (sensor 1) response rate. The ECM receives a signal from the air fuel ratio sensor (sensor 1) while performing active air fuel ratio control and uses it to calculate the air fuel ratio sensor (sensor 1) response rate deterioration level.
If the value for the air fuel ratio sensor (sensor 1) response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.
| Required Sensors/Components | Air fuel ratio sensor (sensor 1) |
| Frequency of Operation | Once per driving cycle |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control performed when following conditions met | - |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idling | Off |
| Engine speed | 1000 rpm or more, and less than 3000 rpm |
| Air fuel ratio sensor status | Activated |
| Engine load | 10% or higher, and less than 100% |
| Catalyst monitor | Not yet |
| Mass air flow | 4 gm/sec or more, and less than 16 gm/sec |
Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
With the engine running, drive the vehicle at approximately 60 to 100 km/h (37 to 62 mph) for 10 minutes or more in a city area [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2A0026.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE and no pending DTC is output, perform the following procedure.
With the engine running, drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2A0026.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, drive the vehicle again under an increased load and then recheck the judgment result.
Refer to DTC P003012.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P003012
Inspect the fuses for circuits related to this system before performing the following procedure.
DTC P2A0026 may be also stored when the air fuel ratio is stuck at rich or lean.
A low air fuel ratio sensor (sensor 1) voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor (sensor 1) voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2A0026 and other DTCs are output | A |
| P2A0026 is output | B |
If any DTCs other than P2A0026 are output, troubleshoot those DTCs first.
A
B
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.
Procedure1
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the output values of the air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2) displayed on the GTS.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| Coolant Temperature |
| Injection Volume |
| A/F (O2) Sensor Current B1S1 |
| A/F (O2) Sensor Current B1S2 |
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
If the sensor output value does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Value |
|---|---|---|---|
| A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1)) |
12.5% | Rich | Below -0.075 mA |
| -12.5% | Lean | Higher than 0.037 mA | |
| A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2)) |
12.5% | Rich | Below -0.86 mA |
| -12.5% | Lean | Higher than 0.33 mA |
Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently higher than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently higher than 0.33 mA.
Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.
Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1, A/F (O2) Sensor Current B1S2.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
Post-procedure1
None.
| Status of A/F (O2) Sensor Current B1S1 | Status of A/F (O2) Sensor Current B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor (Sensor 1) Condition | Proceed to |
|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | A |
| Lean | Lean | Actual air fuel ratio lean | B |
| Rich | Rich | Actual air fuel ratio rich | B |
| Lean | Lean/Rich | Air fuel ratio sensor (sensor 1) malfunction | C |
| Rich | Lean/Rich | Air fuel ratio sensor (sensor 1) malfunction | C |
A
B
C
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P2A0026.
Check the DTC judgment result.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(P2A0026 is output) |
B |
A
B
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>G16E-GTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks in the intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check for exhaust gas leaks.
No gas leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.
Procedure1
Read the Data List when idling.
| Tester Display |
|---|
| Engine Speed |
| Coolant Temperature |
| Fuel Pressure (High) |
| Injection Mode |
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| The value of Fuel Pressure (High) is between 3000 kPag and 5000 kPag | A |
| None of the above conditions are met | B |
A
B
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.
Procedure1
Read the Data List at 3000 rpm.
| Tester Display |
|---|
| Engine Speed |
| Coolant Temperature |
| Fuel Pressure (High) |
| Injection Mode |
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| The value of Fuel Pressure (High) is between 4000 kPag and 20000 kPag | A |
| None of the above conditions are met | B |
A
B
Inspect the port fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL INJECTOR (for Port Injection)>INSPECTION
Perform "Inspection After Repair" after replacing the port fuel injector assembly.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL INJECTOR (for Port Injection)>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Inspect the direct fuel injector assembly.
Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL INJECTOR (for Direct Injection)>INSPECTION
Perform "Inspection After Repair" after replacing the direct fuel injector assembly.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL INJECTOR (for Direct Injection)>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P2A0026.
Check the DTC judgment result.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(P2A0026 is output) |
B |
A
B
Check the fuel lines (for low pressure side) for leaks or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG