89348N
1.REMOVE NO. 1 ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)
89341K
2.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)
89341L
3.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)
89347B
4.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
88211B
5.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense 2)
82113
6.REMOVE NO. 3 ENGINE ROOM WIRE (w/ Wire Harness)
for TMC Made with Parking Support Brake System:
Disengage the clamps to remove the No. 3 engine room wire.
for TMMF Made with Parking Support Brake System:
Disengage the clamps to remove the No. 3 engine room wire.
w/o Parking Support Brake System:
Disengage the clamps to remove the No. 3 engine room wire.
75311
7.REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
When removing the radiator grille (or front panel) emblem, heat the front bumper assembly and radiator grille (or front panel) emblem a heat light.
| Item | Temperature |
|---|---|
·
Front Bumper Assembly ·
Radiator Grille (or front panel) Emblem |
20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper assembly and radiator grille (or front panel) emblem excessively.
| *a | Location Pin |
|
Protective Tape |
Apply protective tape around the radiator grille (or front panel) emblem.
Using a moulding remover D, separate the double-sided tape and disengage the location pins to remove the radiator grille (or front panel) emblem.
Remove the protective tape.
8.REMOVE WIRING HARNESS CONNECTOR (w/o Parking Support Brake System)
for TMC Made:
Disengage the clamp to remove the wiring harness connector.
81220
9.REMOVE FOG LIGHT ASSEMBLY LH
for LED Type:
Click hereVehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY (for 5 Door)>REMOVAL
for Bulb Type:
Click hereVehicle Exterior>LIGHTING (EXT)>FOG LIGHT ASSEMBLY (for 5 Door)>REMOVAL
81210A
10.REMOVE FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
52113D
11.REMOVE FRONT BUMPER EXTENSION LH (w/ Fog Light)
Remove the moulding retainer.
Disengage the claws to remove the front bumper extension LH.
52112D
12.REMOVE FRONT BUMPER EXTENSION RH (w/ Fog Light)
Use the same procedure as for the LH side.
52113D
13.REMOVE FRONT BUMPER EXTENSION LH (w/o Fog Light)
Disengage the claws to remove the front bumper extension LH.
52112D
14.REMOVE FRONT BUMPER EXTENSION RH (w/o Fog Light)
Use the same procedure as for the LH side.
52127C
15.REMOVE FRONT BUMPER HOLE COVER
Disengage the claws.
Disengage the hook to remove the front bumper hole cover.
52129D
16.REMOVE FRONT BUMPER LOWER COVER
Disengage the claws.
Disengage the hook to remove the front bumper lower cover.
53395E
17.REMOVE HOOD TO FRONT END PANEL SEAL
Disengage the clips to remove the hood to front end panel seal.
53155D
18.REMOVE NO. 1 RADIATOR GRILLE SEAL
Remove the 2 screws.
Disengage the claws to remove the No. 1 radiator grille seal.
53101
19.REMOVE RADIATOR GRILLE SUB-ASSEMBLY
Remove the 2 screws and 4 clips.
Disengage the claws to remove the radiator grille sub-assembly.
for TMC Made:
Remove the 2 nuts.
53112E
20.REMOVE NO. 1 LOWER RADIATOR GRILLE
for TMC Made:
Remove the 2 screws.
Disengage the claws to remove the No. 1 lower radiator grille.
except TMC Made:
Remove the 3 screws.
Disengage the claws to remove the No. 1 lower radiator grille.
53879H
21.REMOVE FRONT FENDER LINER RETAINER
Disengage the claw to remove the front fender liner retainer.
Use the same procedure for the RH side and LH side.
22.REMOVE HEADLIGHT ASSEMBLY LH
for Halogen Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>REMOVAL
for LED Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
23.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
52536
24.REMOVE FRONT BUMPER SIDE RETAINER LH
Disengage the claws to remove the front bumper side retainer LH.
52535
25.REMOVE FRONT BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
16681A
26.REMOVE RADIATOR UPPER AIR GUIDE PLATE
Disengage the wire harness clamp.
Disengage the clips to remove the radiator upper air guide plate.
52611
27.REMOVE FRONT BUMPER ENERGY ABSORBER
Disengage the guides to remove the front bumper energy absorber.
88790B
28.SEPARATE THERMISTOR ASSEMBLY
Disengage the clamps to separate the thermistor assembly.
52131A
29.REMOVE FRONT BUMPER REINFORCEMENT
Disengage the wire harness clamps.
Remove the 2 nuts.
Remove the 8 bolts and front bumper reinforcement.
16695A
30.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH
|
Remove in this Direction |
Disengage the claws to remove the front radiator side air guide plate LH as shown in the illustration.
16691A
31.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH
|
Remove in this Direction |
Disengage the claws to remove the front radiator side air guide plate RH as shown in the illustration.
32.REMOVE NO. 2 RADIATOR TO SUPPORT SEAL
for Gasoline Model:
|
Remove in this Direction |
Disengage the claws to remove the No. 2 radiator to support seal as shown in the illustration.
for HV Model:
|
Remove in this Direction |
Disengage the claws to remove the No. 2 radiator to support seal as shown in the illustration.
16595D
33.REMOVE NO. 1 RADIATOR AIR GUIDE LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claws to remove the No. 1 radiator air guide LH as shown in the illustration.
16561D
34.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claws to remove the No. 1 radiator to support seal as shown in the illustration.
57014C
35.REMOVE FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH
If reusing the front side member bracket sub-assembly LH:
Put matchmarks on the front side member bracket sub-assembly LH as shown in the illustration.
Disengage the clamp.
Remove the 5 bolts and front side member bracket sub-assembly LH.
57013D
36.REMOVE FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH
If reusing the front side member bracket sub-assembly RH:
Put matchmarks on the front side member bracket sub-assembly RH as shown in the illustration.
Remove the 5 bolts and front side member bracket sub-assembly RH.
52103A
37.REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY LH (for TMMF Made)
Remove the 3 bolts and front bumper extension sub-assembly LH.
52102B
38.REMOVE FRONT BUMPER EXTENSION SUB-ASSEMBLY RH (for TMMF Made)
Use the same procedure as for the LH side.
51451A
39.REMOVE CENTER ENGINE UNDER COVER
52618
40.REMOVE FRONT BUMPER LOWER ABSORBER
| *a | screw |
| *b | clip |
Remove the clip and 7 screws.
Disengage the claws to remove the front bumper lower absorber.
Remove the 4 grommets.