Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model TMC Made LHD) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0447308 BRAKE ACTUATOR(for Gasoline Model TMC Made LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model TMC Made LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


Hide 44521A 2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

a.

Install the 3 No. 1 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.



Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Temporarily install the brake actuator assembly with the 3 bolts.


b.
C444970E01
2.25,1.563 2.406,1.76 0.156,0.198 10 false 1 0.646,1.135 0.802,1.333 0.156,0.198 10 true 2 2.406,0.76 2.563,0.958 0.156,0.198 10 false 3

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44591 4.INSTALL NO. 1 BRAKE ACTUATOR BRACKET

a.

Temporarily install the No. 1 brake actuator bracket with the 3 bolts.


b.
C444969N01
0.729,0.854 0.885,1.052 0.156,0.198 10 false 1 2.313,0.49 2.469,0.688 0.156,0.198 10 false 2 2.375,1.76 2.615,1.958 0.24,0.198 10 false 3

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 5.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C444973N01
0.333,0.51 0.5,0.708 0.167,0.198 10 true 1 2.844,1.406 3.01,1.604 0.167,0.198 10 true 2 1.604,1.885 1.771,2.083 0.167,0.198 10 true 3

Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.

Fully tighten the bolt and 2 nuts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C444966

Engage the clamp and install a new No. 2 brake tube clamp to the vehicle body.


d.
C444965

Engage the 5 clamps to install the No. 2 brake tube clamp to the brake lines.


e.
C444964

Engage the 5 clamps to install a new No. 1 brake tube clamp to the brake lines.


f.
C444963C01
2.01,1.073 2.365,0.646 2.365,0.646 2.458,0.646 true 1.115,1.948 1.219,1.948 1.219,1.948 1.625,1.604 true 2.156,1.365 2.625,1.125 2.625,1.125 2.719,1.125 true 0.74,1.063 0.844,1.063 0.844,1.063 1.438,1.302 true 1.135,0.458 1.24,0.458 1.24,0.458 1.656,1.24 true 1.833,1.125 1.958,0.417 1.958,0.417 2.052,0.417 true 2.75,1.042 2.948,1.229 0.198,0.188 10 true *a 0.927,1.844 1.125,2.021 0.198,0.177 10 true *b 0.542,0.958 0.708,1.115 0.167,0.156 10 true *c 0.958,0.365 1.125,0.521 0.167,0.156 10 true *d 2.073,0.333 2.24,0.49 0.167,0.156 10 true *e 2.479,0.573 2.646,0.729 0.167,0.156 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




g.
C444974C01
1.75,3.052 2.063,3.208 0.313,0.156 10 false *a 1.073,1.708 1.219,1.865 0.146,0.156 10 true B 2.615,1.438 2.76,1.594 0.146,0.156 10 true B 2.396,0.844 2.542,1 0.146,0.156 10 true A 1.802,1.656 1.948,1.813 0.146,0.156 10 true A 1.292,0.698 1.438,0.854 0.146,0.156 10 true A 0.875,1.177 1.021,1.333 0.146,0.156 10 true A
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 6 brake lines to the brake actuator assembly.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




h.
C444975C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




i.

Return the air conditioning tube and accessory assembly to its original position.

NOTICE:

Do not apply excessive force to the return the air conditioning tube and accessory assembly to its original position..



Hide 88710E 6.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:
HFC-134a (R134a):

ND-OIL 8 or equivalent

HFO-1234yf (R1234yf):

ND-OIL 12 or equivalent



c.

Install the 2 O-rings to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the air conditioning tube and accessory assembly to the air conditioning unit assembly.


e.
C444976

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


g.

Engage the 2 clamps to install the air conditioning tube and accessory assembly.


Hide 164A2 7.INSTALL RESERVE SEALED TANK

a.

Install the reserve sealed tank with the 2 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 55225C 8.INSTALL DASH PANEL HEAT INSULATOR

a.
C444956E01
2.313,0.073 2.469,0.271 0.156,0.198 10 true A

Temporarily install the dash panel heat insulator to the vehicle body with the nut (A) and clamp.

i.
C444955E01
1.417,1.802 1.563,1.958 0.146,0.156 10 true B

Install the nut (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Tighten the nut (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 51451A 9.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 12601B 10.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 14.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 22.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 25. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART