Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP (for TMC Made G16E-GTS) › from 2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0447355 VACUUM PUMP(for TMC Made G16E-GTS) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(for TMC Made G16E-GTS)  INSTALLATION  


PROCEDURE

Hide 29300 1.INSTALL VACUUM PUMP ASSEMBLY

a.

When using new vacuum pump assembly:

i.
C445382C01
1.802,0.938 2.521,0.531 2.521,0.531 2.708,0.531 true 1.24,1.302 0.917,1.552 0.917,1.552 0.729,1.552 false 2.792,0.458 3.021,0.625 0.229,0.167 10 false *1 0.531,1.469 0.75,1.635 0.219,0.167 10 false *2
*1 No. 2 O-ring
*2 No. 4 O-ring
V100135

Engine oil


Apply engine oil to the No. 4 O-ring installed in a new vacuum pump assembly.

NOTICE:

Do not apply engine oil to the No. 2 O-ring.




b.

When reusing the vacuum pump assembly:

i.
C445382C01
1.802,0.938 2.521,0.531 2.521,0.531 2.708,0.531 true 1.24,1.302 0.917,1.552 0.917,1.552 0.729,1.552 false 2.792,0.458 3.021,0.625 0.229,0.167 10 false *1 0.531,1.469 0.75,1.635 0.219,0.167 10 false *2
*1 No. 2 O-ring
*2 No. 4 O-ring
V100135

Engine oil


Install a new No. 2 O-ring to the vacuum pump assembly.


ii.

Apply engine oil to the No. 4 O-ring on the vacuum pump assembly.

NOTICE:

Do not apply engine oil to the No. 2 O-ring.




c.

Apply engine oil to the inner surface of the installation hole.


d.
C445030

Install the vacuum pump assembly so that the oil pipe engages with the hole of the camshaft and the coupling teeth with the grooves on the camshaft tip.

NOTICE:
·

Ensure that the vacuum pump assembly is installed securely.

·

Be careful not to pinch the O-ring.




e.

Install the vacuum pump assembly with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

After installation, check that there are no gaps between the matching surfaces and that the vacuum pump assembly is not installed at an angle.



Hide 25781A 2.CONNECT NO. 3 VACUUM TRANSMITTING HOSE

a.

Connect the No. 3 vacuum transmitting hose to the vacuum pump assembly.


Hide 44774 3.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose, and slide the clamp to secure it.


Hide 16268 4.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Engage the clamp.


b.

Install the No. 1 water by-pass pipe with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 87246 5.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose, and slide the clamp to secure it.


Hide 82121 6.INSTALL ENGINE WIRE

a.

Engage the clamp to install the engine wire.


Hide 23826 7.INSTALL NO. 1 FUEL VAPOR FEED HOSE

a.

Engage the 2 clamps to install the No. 1 fuel vapor feed hose.


Hide 23901 8.INSTALL FUEL TUBE SUB-ASSEMBLY

a.

Engage the clamp to install the fuel tube sub-assembly.


Hide 10.ADD ENGINE COOLANT

Hide 51410 12.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 12601B 14.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY