Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.09–2021.11
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) C

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  U117087  Lost Communication With Brake System Control Module(ch2) Missing Message  


DESCRIPTION

The brake actuator assembly communicates with the ECM and engine stop and start ECU. When the brake actuator assembly does not receive data from the engine stop and start ECU, the engine stop and start ECU stores DTC U117087.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U117087 Lost Communication With Brake System Control Module(ch2) Missing Message No communication from the brake actuator assembly continues.
·

Brake actuator assembly main line or connector

·

Brake actuator assembly


Engine stop and start ECU

WIRING DIAGRAM

except G16E-GTS


C434123E02
1.198,0.74 1.615,0.958 0.417,0.219 10 false LC1H 1.219,1.281 1.656,1.469 0.438,0.188 10 false LC1L 0.167,1.656 0.604,1.844 0.438,0.188 10 false H43 0.156,1.813 1.927,2.021 1.771,0.208 10 false Engine Stop and Start ECU 1.635,0.625 1.865,0.802 0.229,0.177 10 false 15 1.635,1.177 1.865,1.354 0.229,0.177 10 false 16 3.271,0.604 3.531,0.781 0.26,0.177 10 false 10 3.281,1.156 3.542,1.375 0.26,0.219 10 false 21 4.594,0.615 4.948,0.833 0.354,0.219 10 false 11 4.583,1.167 4.802,1.344 0.219,0.177 10 false 22 5.167,0.635 5.385,0.813 0.219,0.177 10 false 12 5.177,1.146 5.396,1.323 0.219,0.177 10 false 13 5.417,0.604 5.854,0.792 0.438,0.188 10 false CAWH 5.417,1.146 5.854,1.333 0.438,0.188 10 false CAWL 5.052,1.667 5.49,1.854 0.438,0.188 10 false H40 5.042,1.823 7,2.188 1.958,0.365 10 false Central Gateway ECU (Network Gateway ECU) 2.469,2.771 2.906,2.958 0.438,0.188 10 false CA2H 1.271,3.177 1.708,3.365 0.438,0.188 10 false GND1 2.917,2.75 3.146,2.927 0.229,0.177 10 false 19 2.917,3.292 3.146,3.469 0.229,0.177 10 false 18 3.375,2.781 3.521,2.958 0.146,0.177 10 false 9 3.281,3.323 3.469,3.5 0.188,0.177 10 false 20 1.219,3.802 1.563,3.99 0.344,0.188 10 false A37 1.219,3.958 2.865,4.344 1.646,0.385 10 false Brake Actuator Assembly 3.458,3.792 3.844,3.979 0.385,0.188 10 false H117 3.438,3.948 5.104,4.354 1.667,0.406 10 false No. 6 Global CAN Junction Connector 2.51,3.302 2.948,3.49 0.438,0.188 10 false CA2L 1.281,3.458 1.719,3.646 0.438,0.188 10 false GND2 1.271,2.854 1.708,3.042 0.438,0.188 10 false IGR 0.365,2.458 1.719,2.615 1.354,0.156 10 false ECU-IGR NO.3 1.031,2.76 1.26,2.938 0.229,0.177 10 false 6 1.031,3.365 1.26,3.542 0.229,0.177 10 false 13 1.031,3.052 1.26,3.229 0.229,0.177 10 false 38 1.802,2.302 3.323,2.531 1.521,0.229 10 false from IGR-NO. 1 Relay


for G16E-GTS


C446924E01
1.198,0.74 1.615,0.958 0.417,0.219 10 false LC1H 1.219,1.281 1.656,1.469 0.438,0.188 10 false LC1L 0.177,1.573 0.615,1.76 0.438,0.188 10 false H43 0.177,1.74 1.948,1.948 1.771,0.208 10 false Engine Stop and Start ECU 1.635,0.625 1.865,0.802 0.229,0.177 10 false 15 1.635,1.177 1.865,1.354 0.229,0.177 10 false 16 3.271,0.604 3.531,0.781 0.26,0.177 10 false 10 3.281,1.156 3.542,1.375 0.26,0.219 10 false 21 4.594,0.615 4.948,0.833 0.354,0.219 10 false 11 4.583,1.167 4.802,1.344 0.219,0.177 10 false 22 5.167,0.635 5.385,0.813 0.219,0.177 10 false 12 5.177,1.146 5.396,1.323 0.219,0.177 10 false 13 5.417,0.604 5.854,0.792 0.438,0.188 10 false CAWH 5.417,1.146 5.854,1.333 0.438,0.188 10 false CAWL 5.052,1.667 5.49,1.854 0.438,0.188 10 false H40 5.042,1.823 7,2.188 1.958,0.365 10 false Central Gateway ECU (Network Gateway ECU) 2.469,2.771 2.906,2.958 0.438,0.188 10 false CA2H 1.271,3.177 1.708,3.365 0.438,0.188 10 false GND1 2.917,2.75 3.271,3.052 0.354,0.302 10 false 36 2.917,3.292 3.271,3.583 0.354,0.292 10 false 37 3.375,2.781 3.521,2.958 0.146,0.177 10 false 9 3.281,3.323 3.469,3.5 0.188,0.177 10 false 20 1.24,3.802 1.833,4.052 0.594,0.25 10 false A108 1.229,3.969 2.875,4.354 1.646,0.385 10 false Brake Actuator Assembly 3.458,3.792 3.844,3.979 0.385,0.188 10 false H117 3.438,3.948 5.104,4.354 1.667,0.406 10 false No. 6 Global CAN Junction Connector 2.51,3.302 2.948,3.49 0.438,0.188 10 false CA2L 1.281,3.458 1.719,3.646 0.438,0.188 10 false GND2 1.271,2.854 1.708,3.042 0.438,0.188 10 false IGR 1.031,2.76 1.385,3.021 0.354,0.26 10 false 12 1.094,3.354 1.344,3.552 0.25,0.198 10 false 1 1.031,3.052 1.396,3.313 0.365,0.26 10 false 25 1.802,2.083 3.146,2.479 1.344,0.396 10 false from Engine Stop and Start ECU


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
except G16E-GTS A
for G16E-GTS B



A

2.CHECK FOR CAN BUS BRANCH WIRE

B

23.CHECK FOR CAN BUS BRANCH WIRE
2.CHECK FOR CAN BUS BRANCH WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
H117-10 (CANH) - H117-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
H117-10 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
H117-21 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
H117-10 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
H117-21 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
NG (+B short or Short to ground) D



A

3.CLEAR DTC

B

5.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY MAIN BUS)

C

11.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)

D

17.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392

Result:
Result Proceed to
DTC U117087 is output A
DTC U117087 is not output B



A

B

5.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-9 (CANH) - H117-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)

NG

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY)
6.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-11 (CANH) - H117-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH BUS)

NG

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
7.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-10 (CANH) - H117-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

10.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the A37 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-19 (CA2H) - A37-18 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-12 (CAWH) - H40-13 (CAWL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

10.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-15 (LC1H) - H43-16 (LC1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

11.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-9 (CANH) - H117-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)

NG

14.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
12.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-11 (CANH) - H117-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)

NG

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
13.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-10 (CANH) - H117-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

16.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
14.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the A37 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-19 (CA2H) - A37-18 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-12 (CAWH) - H40-13 (CAWL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-15 (LC1H) - H43-16 (LC1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-9 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-20 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-9 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H117-20 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)

NG

20.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-11 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-22 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-11 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H117-22 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)

NG

21.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
19.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-10 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-21 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-10 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H117-21 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

22.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
20.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the A37 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-19 (CA2H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A37-18 (CA2L) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A37-19 (CA2H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A37-18 (CA2L) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

21.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-12 (CAWH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-13 (CAWL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-12 (CAWH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-13 (CAWL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-15 (LC1H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-16 (LC1L) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-15 (LC1H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H43-16 (LC1L) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

23.CHECK FOR CAN BUS BRANCH WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
H117-10 (CANH) - H117-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
H117-10 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
H117-21 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
H117-10 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
H117-21 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
NG (+B short or Short to ground) D



A

24.CLEAR DTC

B

26.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY MAIN BUS)

C

32.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)

D

38.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
24.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

Result:
Proceed to
NEXT



NEXT

25.CHECK FOR DTC
25.CHECK FOR DTC
a.

Check for DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392

Result:
Result Proceed to
DTC U117087 is output A
DTC U117087 is not output B



A

B

26.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-9 (CANH) - H117-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

27.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)

NG

29.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY)
27.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-11 (CANH) - H117-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

28.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH BUS)

NG

30.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
28.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-10 (CANH) - H117-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

31.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU)
29.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the A108 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A108-36 (CA2H) - A108-37 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

30.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-12 (CAWH) - H40-13 (CAWL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

31.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-15 (LC1H) - H43-16 (LC1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

32.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-9 (CANH) - H117-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

33.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)

NG

35.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
33.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-11 (CANH) - H117-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

34.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)

NG

36.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
34.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-10 (CANH) - H117-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

37.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
35.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the A108 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A108-36 (CA2H) - A108-37 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

36.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-12 (CAWH) - H40-13 (CAWL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

37.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-15 (LC1H) - H43-16 (LC1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

38.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-9 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-20 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-9 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H117-20 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)

NG

41.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
39.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-11 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-22 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-11 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H117-22 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

40.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)

NG

42.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
40.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU BRANCH BUS)
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H117-10 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-21 (CANL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H117-10 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H117-21 (CANL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

43.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
41.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the A108 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A108-36 (CA2H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A108-37 (CA2L) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A108-36 (CA2H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A108-37 (CA2L) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (BRAKE ACTUATOR ASSEMBLY - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

42.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-12 (CAWH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-13 (CAWL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-12 (CAWH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-13 (CAWL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)

43.CHECK FOR SHORT IN CAN BUS WIRES (ENGINE STOP AND START ECU)
a.

Reconnect the H117 No. 6 global CAN junction connector.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-15 (LC1H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-16 (LC1L) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-15 (LC1H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H43-16 (LC1L) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (ENGINE STOP AND START ECU - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)