Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449605 MANUAL TRANSAXLE UNIT A

EA67F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 31121 1.REMOVE NO. 1 CLUTCH HOUSING COVER

a.
C450901

Remove the No. 1 clutch housing cover from the front transaxle case.


Hide 31478 2.REMOVE RELEASE CYLINDER BLEEDER PLUG CAP

a.
C450902

Remove the release cylinder bleeder plug cap from the release cylinder bleeder plug.


Hide 3.REMOVE RELEASE CYLINDER BLEEDER PLUG

a.
C450903

Remove the release cylinder bleeder plug from the clutch release bleeder sub-assembly.


Hide 31407B 4.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31224 5.REMOVE CLUTCH RELEASE BEARING PLATE

Hide 31400 6.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31483 7.REMOVE CLUTCH RELEASE CYLINDER TO BLEEDER TUBE

Hide 335A0 8.REMOVE CONTROL CABLE BRACKET

a.
C450904

Remove the 3 bolts and control cable bracket from the manual transmission case.


Hide 9.REMOVE SELECTING BELL CRANK ASSEMBLY

a.
C450905

Remove the 2 bolts and selecting bell crank assembly from the manual transmission case.


Hide 84210 10.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C450906N01
0.698,1.073 1.563,1.177 true 0.396,0.979 0.854,1.177 0.458,0.198 10 false SST

Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.

SST
09816-30010  


Hide 84545 11.REMOVE NEUTRAL POSITION SWITCH

a.
C450907N01
1.208,1.5 1.583,1.115 true 0.813,1.427 1.156,1.615 0.344,0.188 10 true SST

Using SST, remove the neutral position switch and gasket from the manual transmission case.

SST
09816-30010  


Hide 89413B 13.REMOVE TRANSMISSION REVOLUTION SENSOR

Hide 33290 14.REMOVE NO. 1 LOCK BALL ASSEMBLY

a.
C450909

Remove the No. 1 lock ball assembly from the manual transmission case.


Hide 33290B 15.REMOVE NO. 2 LOCK BALL ASSEMBLY

a.
C450910

Remove the No. 2 lock ball assembly from the manual transmission case.


Hide 33295B 16.REMOVE SHIFT GATE PIN

a.
C450911

Remove the shift gate pin from the manual transmission case.


Hide 17.REMOVE SHIFT AND SELECT LEVER ASSEMBLY

a.
C450912

Remove the 4 bolts and shift and select lever assembly from the manual transmission case.


Hide 33261F 18.REMOVE SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN

a.
C450913C01
1.156,0.042 1.365,0.24 0.208,0.198 10 true *a 1.573,1.344 1.76,1.542 0.188,0.198 10 true *b
*a Press and hold
*b Pull out the shift and select pin.


While pressing in the shift and select lever shaft straight pin as far as it will go, pull out the shift and select lever shaft straight pin to remove it.


b.

Remove the spring.


Hide 33223B 19.REMOVE SHIFT ARM PIVOT O-RING

a.
C450914

Remove the O-ring from the shift and select lever shaft straight pin.


Hide 33101A 20.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C450915

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33104 21.REMOVE DRAIN PLUG

a.
C450916

Remove the drain plug and gasket from the manual transmission case.


Hide 30300 22.FIX MANUAL TRANSAXLE ASSEMBLY

a.
C450917C01
2.448,1.885 2.75,1.885 false 0.708,1.875 1.073,1.875 false 0.531,1.771 0.844,1.969 0.313,0.198 10 false *a 2.781,1.792 3.094,1.99 0.313,0.198 10 false *a
*a Wooden Block


Place the manual transaxle assembly on wooden blocks.


Hide 33275C 23.REMOVE SHIFT DETENT BALL

a.
C450918

Using a 6 mm hexagon wrench, remove the 4 detent ball plugs from the front transaxle case.


b.

Using a magnet hand, remove the 4 spring seats, 4 springs and 4 shift detent balls from the front transaxle case.


Hide 33451H 24.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C450919

Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.


Hide 33111A 25.REMOVE MANUAL TRANSMISSION CASE PLUG

a.
C450920N01
1.969,0.698 2.51,0.542 true 2.552,0.458 3.01,0.656 0.458,0.198 10 false SST

Using SST and 27 mm straight hexagon, remove the manual transmission case plugs from the manual transmission case.

SST
09816-30010  


Hide 33111 26.REMOVE MANUAL TRANSMISSION CASE

a.
C450922

Remove the 8 bolts from the front transaxle case side.


b.
C450923

Remove the 10 bolts from the manual transmission case side.


c.
C450924

Using snap ring pliers, keep the snap ring stretched and remove the manual transmission case.


Hide 33124C 27.REMOVE NO. 1 OIL RECEIVER PIPE

a.
C450925

Remove the bolt and No. 1 receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 1 oil receiver pipe.



Hide 33176B 28.REMOVE TRANSMISSION OIL SEPARATOR

a.
C450926

Remove the 2 bolts and transmission oil separator from the manual transmission case.


Hide 33176B 29.REMOVE TRANSMISSION OIL SEPARATOR

a.
C450942

Remove the 2 bolts and transmission oil separator from the front transaxle case.


Hide 33243F 30.REMOVE 3RD AND 4TH SHIFT FORK SHAFT

a.
C450927C01
1.333,0.385 1.573,0.219 true 1.615,0.115 1.854,0.438 0.24,0.323 10 false *1
*1 3rd and 4th Shift Fork Shaft


Using a 5 mm pin punch and a hammer, tap out the slotted spring pin until the 3rd and 4th shift fork shaft becomes free.

NOTICE:
·

Do not allow the slotted spring pin to contact the gear.

·

Do not fully extract the pin from the No. 2 gear shift fork




b.
C450928C01
2.438,1.042 2.865,0.375 true 2.885,0.281 3.198,0.479 0.313,0.198 10 false *1
*1 No. 2 Gear Shift Head
V100155

Protective Tape


Apply protective tape to the locations shown in the illustration.


c.

Using a 5 mm pin punch and a hammer, tap out the slotted spring pin until the 3rd and 4th shift fork shaft becomes free.

NOTICE:
·

Do not allow the slotted spring pin to contact the No. 5 gear shift fork shaft.

·

Do not fully extract the pin from the No. 2 gear shift head.




d.
C450929C01
2.385,0.729 2.719,0.396 false 2.406,1.625 2.958,1.104 true 2.75,0.292 3.021,0.542 0.271,0.25 10 false *1 2.969,1.021 3.24,1.344 0.271,0.323 10 false *2
*1 3rd and 4th Shift Fork Shaft
*2 No. 2 Gear Shift Head


Remove the 3rd and 4th shift fork shaft and No. 2 gear shift head from the No. 2 gear shift fork and front transaxle case.


e.

Remove the 2 slotted spring pins.


Hide 33246C 31.REMOVE NO. 5 GEAR SHIFT FORK SHAFT

a.
C450930

Using a screwdriver, remove the E-ring from the shift arm pivot.


b.
C450931

Remove the shift arm pivot from the shift arm.


c.
C450932

Remove the No. 5 gear shift fork shaft from the front transaxle case.


d.
C450933

Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 3 gear shift head.


e.

Remove the No. 3 gear shift head from the No. 5 gear shift fork shaft.


Hide 33222F 32.REMOVE SHIFT ARM

a.
C450934

Remove the shift arm from the front transaxle case.


Hide 33245H 33.REMOVE REVERSE SHIFT FORK SHAFT

a.
C450935

Remove the bolt from the reverse shift fork shaft.


b.
C450936

Remove the reverse shift fork shaft from the front transaxle case.


Hide 34.INSPECT REVERSE IDLER GEAR THRUST CLEARANCE

Hide 35.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

Hide 33402 36.REMOVE REVERSE IDLER GEAR

a.
C450937

Remove the reverse idler gear shaft by sliding and lifting it.


b.
C450938

Remove the reverse idler gear, needle roller bearing and reverse idler thrust washer from the reverse idler gear shaft.


Hide 37.REMOVE INPUT SHAFT, NO. 1 OUTPUT SHAFT AND NO. 2 OUTPUT SHAFT

a.
C450939N01
1.99,1.417 1.99,1.125 false 1.896,1.479 2.354,1.677 0.458,0.198 10 false SST

Bend left and right sides of SST in opposite directions.

SST
09312-52010  

NOTICE:

Do not bend SST more than necessary.



b.
C450940N01
2.406,1.292 2.646,1.021 2.646,1.021 2.219,1.073 true 2.708,0.917 3.167,1.115 0.458,0.198 10 false SST

Install SST to the top and bottom of the No. 3 transmission hub sleeve.

SST
09312-52010  

NOTICE:

Make sure that SST does not easily come loose.


HINT:

Install SST in a tensioned state so that the No. 3 transmission hub sleeve does not shift out of position.



c.
C116196

Remove the 3 shafts at the same time.


Hide 38.REMOVE DIFFERENTIAL GEAR ASSEMBLY

a.
C450943

Remove the differential gear assembly from the front transaxle case.


Hide 33449 39.REMOVE TRANSMISSION MAGNET

a.
C450944

Remove the transmission magnet from the front transaxle case.


Hide 33212A 40.REMOVE NO. 1 GEAR SHIFT FORK

a.
C450945

Remove the No. 1 gear shift fork from the No. 1 output shaft assembly.


Hide 33213G 41.REMOVE NO. 2 GEAR SHIFT FORK

a.
C450946

Remove the No. 2 gear shift fork from the No. 1 gear shift fork.


Hide 33214G 42.REMOVE NO. 3 GEAR SHIFT FORK

a.
C450947

Remove the No. 3 gear shift fork from the No. 2 output shaft assembly.


Hide 33211 43.REMOVE REVERSE SHIFT FORK

a.
C450948

Remove the reverse shift fork from the No. 3 gear shift fork.


Hide 33321A 44.REMOVE OUTPUT SHAFT REAR BEARING

a.
C450949N01
1.646,1.729 1.031,2.052 1.031,2.052 1.625,1.469 true 0.74,1.979 1.052,2.156 0.313,0.177 10 true SST

Using SST, remove the output shaft rear bearing outer race from the manual transmission case.

SST
09387-00041  
09387-02020  


Hide 33321H 45.REMOVE OUTPUT SHAFT REAR BEARING SHIM

a.
C450950

Remove the output shaft rear bearing shim from the manual transmission case.


Hide 33322A 46.REMOVE NO. 2 OUTPUT SHAFT REAR BEARING

a.
C450951N01
1.448,1.771 0.99,1.969 0.99,1.969 1.448,1.51 true 0.656,1.906 0.979,2.073 0.323,0.167 10 true SST

Using SST, remove the No. 2 output shaft rear bearing outer race from the manual transmission case.

SST
09387-00041  
09387-02020  


Hide 33321H 47.REMOVE OUTPUT SHAFT REAR BEARING SHIM

a.
C450952

Remove the output shaft rear bearing shim from the manual transmission case.


Hide 33134B 48.REMOVE OUTPUT SHAFT COVER

a.
C450953

Remove the output shaft cover from the manual transmission case.


Hide 33242L 49.REMOVE SHIFT FORK SHAFT BEARING

a.
C450954N01
1.146,1.583 0.354,1.01 0.354,1.01 0.948,0.677 true 0.354,1.01 0.563,1.01 false 0.063,0.938 0.521,1.135 0.458,0.198 10 false SST

Using SST, remove the 4 shift fork shaft bearings from the manual transmission case.

SST
09387-00041  (09387-01021)
09527-20011  
09612-65014  


Hide 33261K 50.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C450955N01
1.042,1.625 0.365,0.573 0.365,0.573 0.896,0.708 true 0.073,0.5 0.531,0.698 0.458,0.198 10 false SST

Using SST, remove the shift and select lever shaft needle roller bearing from the manual transmission case.

SST
09387-00041  (09387-01021)
09612-65014  


Hide 33311P 51.REMOVE INPUT SHAFT REAR BEARING SHAFT SNAP RING

a.
C450956

Using snap ring pliers, remove the input shaft rear bearing shaft snap ring from the manual transmission case.


Hide 33311A 52.REMOVE INPUT SHAFT FRONT BEARING

a.
C450957

Remove the bolt and bearing lock plate from the front transaxle case.


b.
C450958N01
0.625,1.51 1.063,1.51 true 0.25,1.427 0.583,1.615 0.333,0.188 10 true SST

Using SST, remove the input shaft front bearing from the front transaxle case.

SST
09612-30012  


Hide 31105D 53.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C450959

Using a screwdriver with its tip wrapped with protective tape, remove the front transaxle case oil seal from the front transaxle case.


Hide 33321N 54.REMOVE OUTPUT SHAFT FRONT BEARING

a.
C450960N01
1.479,1.375 1.073,0.938 1.073,0.938 1.333,1.563 true 1.083,0.927 1.313,0.813 false 0.792,0.875 1.25,1.073 0.458,0.198 10 false SST

Using SST, remove the output shaft front bearing from the front transaxle case.

SST
09387-00041  
09387-02020  
09527-17011  


Hide 33134B 55.REMOVE OUTPUT SHAFT COVER

a.
C450961

Remove the output shaft cover from the front transaxle case.


Hide 33322B 56.REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING

a.
C450962N01
1.542,1.344 1.167,0.917 1.167,0.917 1.417,1.542 true 1.177,0.906 1.396,0.844 false 0.875,0.833 1.188,1.167 0.313,0.333 10 false SST

Using SST, remove the No. 2 output shaft front bearing outer race from the front transaxle case.

SST
09387-00041  
09387-02020  
09527-17011  


Hide 33134B 57.REMOVE OUTPUT SHAFT COVER

a.
C450963

Remove the output shaft cover from the front transaxle case.


Hide 33111J 58.REMOVE MANUAL TRANSMISSION CASE STRAIGHT PIN

a.
C450964

Remove the 3 manual transmission case straight pins from the front transaxle case.


Hide 33242L 59.REMOVE SHIFT FORK SHAFT BEARING

a.
C450965N01
0.417,0.635 0.802,0.635 false 2.917,0.438 3,0.594 false 0.125,0.552 0.583,0.75 0.458,0.198 10 false SST 3.031,0.563 3.385,0.74 0.354,0.177 10 false SST

Using SST, remove the 4 shift fork shaft bearings from the front transaxle case.

SST
09387-00041  (09387-01021)
09612-65014  


Hide 41311F 61.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C450967

Using a brass bar and a hammer, remove the front differential case rear tapered roller bearing outer race and front differential case rear shim from the manual transmission case.


b.
C450968C01
2.188,1.115 2.469,1.229 2.469,1.229 2.219,1.521 false 1.76,1.406 2.469,1.229 2.469,1.229 1.885,1.469 true 2.865,0.333 3.177,0.49 0.313,0.156 10 false *a 0.188,0.531 0.5,0.688 0.313,0.156 10 false *b 2.51,1.146 3.01,1.375 0.5,0.229 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case rear tapered roller bearing from the front No. 1 differential case sub-assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60011  (09951-00540)


Hide 43410M 63.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C459781N01
0.99,1.885 1.438,2.104 false 0.677,1.802 1.135,2 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the transmission sleeve yoke.

SST
09308-00010  

NOTICE:

Be careful not to damage the transmission sleeve yoke.



Hide 41311E 64.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C450969N01
1.521,1.208 1.156,0.802 1.156,0.802 1.385,1.385 true 1.156,0.802 1.375,0.688 true 0.854,0.74 1.156,0.906 0.302,0.167 10 true SST

Using SST, remove the front differential case front tapered roller bearing outer race from the front transaxle case.

SST
09387-00041  
09387-02020  
09527-17011  


b.
C459782C01
2.281,1.656 2.677,1.823 2.677,1.823 2.323,2.292 false 1.781,1.948 2.677,1.823 2.677,1.823 1.865,2.031 true 0.521,2.271 1.417,2.271 true 0.531,1.844 1.51,1.844 true 0.333,2.198 0.646,2.354 0.313,0.156 10 false *1 0.365,1.771 0.677,1.927 0.313,0.156 10 false *2 3.135,0.719 3.365,0.938 0.229,0.219 10 false *a 0.135,1 0.448,1.156 0.313,0.156 10 false *b 2.74,1.76 3.198,1.958 0.458,0.198 10 false SST
*1 Front Differential Case Front Tapered Roller Bearing
*2 Transmission Sleeve Yoke
*a Turn
*b Hold


Using SST, remove the front differential case front tapered roller bearing and transmission sleeve yoke from the front No. 1 differential case sub-assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60011  (09951-00410)