Home › Engine / Hybrid System › G16E-GTS (FUEL) › FUEL PUMP (for High Pressure) › from 2020.09
RM36W0E _51 Engine / Hybrid System _095688 G16E-GTS FUEL _0449364 FUEL PUMP(for High Pressure) A

G16E-GTS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Fuel pump assembly (for high pressure side) Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 5.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 6.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55734A 7.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55735A 8.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 12601B 11.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 25860 12.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

Hide 23901 13.DISCONNECT NO. 1 FUEL TUBE SUB-ASSEMBLY

a.
A472034

Disconnect the No. 1 fuel tube sub-assembly from the No. 2 fuel tube sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23841K 14.REMOVE FUEL PIPE CLAMP

a.
A472035

Remove the fuel pipe clamp from the No. 2 fuel tube sub-assembly.


Hide 23902 15.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A472036

Remove the bolt.


b.

Remove the No. 2 fuel tube sub-assembly from the fuel delivery pipe sub-assembly and fuel pump assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 16296 16.DISCONNECT NO. 8 WATER BY-PASS HOSE

a.
A472037

Slide the clip and disconnect the No. 8 water by-pass hose.


Hide 16261G 17.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
A472072

Slide the clip and disconnect the No. 1 water by-pass hose.


Hide 23801P 18.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A474477

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


b.
A476551

Remove the bolt.


c.
A474478

Using an 8 mm socket wrench, loosen the 2 bolts of the fuel pump assembly.


d.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.


Hide 82121 19.DISCONNECT ENGINE WIRE

a.
A472039

Disconnect the 2 connectors.


b.

Remove the bolt.


c.

Disengage the clamp and disconnect the engine wire.


Hide 25761B 20.DISCONNECT NO. 1 VACUUM TRANSMITTING HOSE

a.
A472040

Disengage the 2 clamps and disconnect the No. 1 vacuum transmitting hose.


Hide 17893 21.SEPARATE INTAKE AIR RESONATOR

a.
A472041

Remove the bolt and separate the intake air resonator from the fuel pump flange.


Hide 23100X 22.REMOVE FUEL PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


a.
A476552

Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly.


b.
A464878

Remove the O-ring from the fuel pump assembly.


c.
A472044

Remove the fuel pump lifter assembly from the fuel pump lifter guide.


d.
A472045

Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.