Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for RHD) › 2020.09–2021.04
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0432677 AIR CONDITIONING UNIT(for RHD) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for RHD)  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

a.

Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I117109C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the 6 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Temporarily install the nut.

NOTICE:

Do not fully tighten the nut.



Hide 55306A 3.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

NOTICE:

Do not fully tighten the screw.



Hide 4.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Tighten the 3 bolts, screws and nut in the order shown in the illustration to install the air conditioner unit assembly.

I117110N01
3.854,0.917 3.99,1.115 0.135,0.198 10 true 1 2.479,0.813 2.615,1.01 0.135,0.198 10 true 2 4.573,0.875 4.708,1.073 0.135,0.198 10 true 3 4.635,2.313 4.771,2.51 0.135,0.198 10 true 4 3.031,2.469 3.167,2.667 0.135,0.198 10 true 5

Torque:
Bolt : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 82141 5.INSTALL INSTRUMENT PANEL WIRE

a.

Engage the each clamp to install the instrument panel wire.

I116171C01
5.49,5.219 5.75,5.438 0.26,0.219 12 true *A 0.75,4.385 1.042,4.635 0.292,0.25 12 true *A 1.563,0.271 1.781,0.479 0.219,0.208 10 true *a 0.979,0.656 1.198,0.865 0.219,0.208 10 true *a 6.76,0.844 6.979,1.052 0.219,0.208 10 true *a 6.813,1.229 7.031,1.438 0.219,0.208 10 true *a 5.646,4.667 5.865,4.875 0.219,0.208 10 true *a 5.625,0.49 5.844,0.698 0.219,0.208 10 true *b 3.146,0.292 3.365,0.5 0.219,0.208 10 true *b 4.125,0.281 4.344,0.49 0.219,0.208 10 true *b 4.135,0.667 4.354,0.875 0.219,0.208 10 true *b 3.781,1.083 4,1.292 0.219,0.208 10 true *b 3.344,0.76 3.563,0.969 0.219,0.208 10 true *b 2.802,2.677 3.021,2.885 0.219,0.208 10 true *b 4.49,2.76 4.708,2.969 0.219,0.208 10 true *b 5.083,2.719 5.323,2.927 0.24,0.208 10 true *b 5.802,2.75 6.042,2.958 0.24,0.208 10 true *b 6.49,2.594 6.729,2.802 0.24,0.208 10 true *b 5.208,3.031 5.448,3.24 0.24,0.208 10 true *b 4.865,4.792 5.104,5 0.24,0.208 10 true *b 4.875,5.302 5.115,5.51 0.24,0.208 10 true *b
*A for Cold Area Specification Vehicles - -
*a Guide *b Clamp



b.

Connect the each connector.


c.

for Cold Area Specification Vehicles:

i.

Engage the guide to connect the ground wire with the bolt to the No. 1 instrument panel brace sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the connector.



d.

Connect the instrument panel wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Install the 4 ground wires with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

for Manual Air Conditioning System:

i.
I115686

Engage the clamp.


ii.

Connect the connector.



g.

for Automatic Air Conditioning System:

i.

Engage the clamp.


ii.
I116396

Connect the 2 connectors.



h.

for Manual Air Conditioning System Single Layer Type:

i.
I115683

Engage the clamp.


ii.

Connect the 2 connectors.



i.

for Manual Air Conditioning System Double Layer Type:

i.
I115684

Engage the clamps.


ii.

Connect the 3 connectors.



j.

for Automatic Air Conditioning System:

i.
I115682

Engage the clamp.


ii.

Connect the connector.



k.
I115680

Install the instrument panel junction block assembly RH with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


l.
I115677

Engage the clamps.


Hide 6.INSTALL TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver)

Hide 7.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 55308B 8.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for TFTM Made)

a.

Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.

Torque:
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 83108 9.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 88539G 10.INSTALL COOLER UNIT DRAIN HOSE GROMMET

a.
I117113C01
1.865,2.927 1.917,2.688 false 2.885,2.917 2.781,2.688 false 1.771,2.927 2.083,3.125 0.313,0.198 10 false *a 2.844,2.938 3.156,3.135 0.313,0.198 10 false *a
*a Lip


Install a new cooler unit drain hose grommet.

NOTICE:
·

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.

·

Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.




Hide 88539J 11.INSTALL DRAIN COOLER HOSE

a.
I115675

Connect the drain cooler hose.


Hide 55216C 12.INSTALL NO. 4 DASH PANEL INSULATOR PAD

a.

Engage the clips to install the No. 4 dash panel insulator pad.

I116330


Hide 87212 13.INSTALL NO. 1 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 87212H 14.INSTALL NO. 4 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 87212F 15.INSTALL NO. 2 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 58510D 16.INSTALL FRONT FLOOR CARPET ASSEMBLY (for Cold Area Specification Vehicles)

a.

Install the front floor carpet assembly with the 2 clips as shown in the illustration.

I117114


Hide 87212J 17.INSTALL NO. 5 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 87212G 18.INSTALL NO. 3 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 58510D 19.INSTALL FRONT FLOOR CARPET ASSEMBLY (except Cold Area Specification Vehicles)

a.

Install the front floor carpet assembly with the 2 clips as shown in the illustration.

I116331


Hide 77306 20.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 58569D 21.INSTALL FRONT FLOOR CAUTION PLATE COVER (for Cold Area Specification Vehicles)

a.
I115777

Engage the guide and claw to install the front floor caution plate cover.


Hide 23.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55084E 24.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116313

Engage the clamp to install the No. 1 heater to register duct sub-assembly.


b.

Install the clip.


Hide 55085 25.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116314

Engage the clamp to install the No. 2 heater to register duct sub-assembly.


b.

Install the clip.


Hide 55086A 26.INSTALL CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I115666

Engage the clamp to install the center heater to register duct sub-assembly.


b.

Install the clip.


Hide 27.INSTALL STEERING COLUMN ASSEMBLY

Hide 87211 28.INSTALL NO. 1 AIR DUCT

a.
I116312

Engage the claws to install the No. 1 air duct.


b.

Install the 2 bolts.


Hide 16290F 31.INSTALL NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 88716A 32.INSTALL COOLER REFRIGERANT LIQUID PIPE A (except 1KR-FE, G16E-GTS)

Hide 88707 33.INSTALL SUCTION PIPE SUB-ASSEMBLY (except 1KR-FE, G16E-GTS)

Hide 88710E 34.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE, G16E-GTS)

Hide 55225 35.INSTALL DASH PANEL HEAT INSULATOR (for G16E-GTS)

Hide 55701J 36.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install outer cowl top panel sub-assembly with the 12 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
I116310

Engage the clamp.


c.

for Cold Area Specification Vehicles:

i.
I116674

Connect the connector.


ii.

Engage the clamps.



Hide 55815E 37.INSTALL NO. 1 FRONT VENTILATOR SEAL

a.
I116309

Engage the claws to install the No. 1 front ventilator seal.


Hide 55735A 38.INSTALL WATER GUARD PLATE LH

a.
I116308

Engage the claws to install the water guard plate LH.


Hide 39.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 41.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 51451A 46.INSTALL CENTER ENGINE UNDER COVER (except G16E-GTS)

Hide 51410 47.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for G16E-GTS)

Hide 49.PERFORM REGISTRATION (w/ Stop And Start System)