Home › Engine / Hybrid System › G16E-GTS (LUBRICATION) › OIL PUMP › from 2020.09
RM36W0E _51 Engine / Hybrid System _095911 G16E-GTS LUBRICATION _0449904 OIL PUMP A

G16E-GTS LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301C 1.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 11310 2.INSTALL TIMING CHAIN COVER ASSEMBLY

a.
A474248

Install 2 new O-rings to the cylinder block sub-assembly.


b.

Clean the contact surfaces of the timing chain cover assembly, oil pan sub-assembly and cylinder block sub-assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A474249C02
1.01,1.021 1.323,1.219 0.313,0.198 10 false *a 0.594,0.177 0.906,0.375 0.313,0.198 10 false *a 3.563,0.167 3.875,0.365 0.313,0.198 10 false *b
*a Timing Chain Cover Assembly Side *b Engine Assembly Side



c.

Clean the contact surfaces of the timing chain cover assembly, oil pan sub-assembly and cylinder block sub-assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A474250C02
2.698,0.667 3.177,0.865 true 2.26,2.635 2.99,2.875 0.729,0.24 10 false A - A (★) 1.927,3.031 2.135,3.292 0.208,0.26 10 false *d 2.813,2.844 3.021,3.104 0.208,0.26 10 false *c 2.438,1.646 2.646,1.906 0.208,0.26 10 false *b 2.521,0.563 2.729,0.823 0.208,0.26 10 false *a 3.146,1.792 3.333,1.99 0.188,0.198 10 true ★ 4.563,1.979 4.75,2.177 0.188,0.198 10 true ★ 5.146,1.635 5.354,1.896 0.208,0.26 10 false *b 2.844,2.292 3.01,2.49 0.167,0.198 10 true A 3.156,2.292 3.323,2.49 0.167,0.198 10 true A
*a 2.5 to 3.5 mm (0.0984 to 0.138 in.) *b 10 mm (0.394 in.)
*c 4.0 to 6.0 mm (0.157 to 0.236 in.) *d 3.0 to 4.0 mm (0.118 to 0.157 in.)
V100155

Seal Packing - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Clean the surfaces with non-residue solvent before applying seal packing.

·

Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




d.

Align the oil pump drive rotor groove of the timing chain cover assembly.

A474251


e.
P000601C60
2.458,0.198 2.24,0.198 2.24,0.198 1.99,1.188 false 2.521,0.115 2.813,0.292 0.292,0.177 10 false *a
*a Adhesive


Apply adhesive to 5 and a half threads or more of the end of the bolts (A, B).

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
A474246E01
0.708,0.219 0.865,0.417 0.156,0.198 10 true A 0.313,1.167 0.469,1.365 0.156,0.198 10 true A 0.229,2.042 0.385,2.24 0.156,0.198 10 true A 0.333,2.948 0.49,3.146 0.156,0.198 10 false A 0.927,3.198 1.083,3.396 0.156,0.198 10 true A 2.479,3.188 2.635,3.385 0.156,0.198 10 true A 2.885,2.938 3.042,3.135 0.156,0.198 10 true A 3.208,1.875 3.365,2.073 0.156,0.198 10 true A 3.104,1.042 3.26,1.24 0.156,0.198 10 true A 2.896,0.396 3.052,0.594 0.156,0.198 10 true A 2.083,0.094 2.24,0.292 0.156,0.198 10 true B 1.708,1.698 1.865,1.896 0.156,0.198 10 true C

Temporarily install the timing chain cover assembly with the 11 bolts and a new bolt (C) and seal washer.

Bolt Length:
Item Length
Bolt (A) 25 mm (0.9843 in.)
Bolt (B) 20 mm (0.7874 in.)
Bolt (C) 40 mm (1.5748 in.)



g.

Install the timing chain cover assembly with the 11 bolts and a new bolt (C) and seal washer in the order shown in the illustration.

A480686C01
1.875,0.823 2.167,1.01 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.719,0.083 4.031,0.281 0.313,0.198 10 false *b 1.656,0.719 1.823,0.917 0.167,0.198 10 true *c 1.031,0.167 1.198,0.365 0.167,0.198 10 true A 2.875,0.281 3.042,0.479 0.167,0.198 10 true A 2.229,0.052 2.396,0.25 0.167,0.198 10 true B 3.031,0.823 3.198,1.021 0.167,0.198 10 true A 3.115,1.51 3.281,1.708 0.167,0.198 10 true A 2.865,2.375 3.031,2.594 0.167,0.219 10 true A 2.531,2.573 2.698,2.76 0.167,0.188 10 true A 1.208,2.563 1.375,2.75 0.167,0.188 10 true A 0.729,2.375 0.896,2.563 0.167,0.188 10 false A 0.646,1.646 0.813,1.833 0.167,0.188 10 true A 0.74,0.948 0.906,1.135 0.167,0.188 10 true A 1.854,1.375 2.021,1.563 0.167,0.188 10 true C 4.24,1.635 4.365,1.813 0.125,0.177 10 true 2 4.323,0.948 4.448,1.156 0.125,0.208 10 true 3 4.625,0.146 4.76,0.333 0.135,0.188 10 true 4 5.792,0.042 5.927,0.229 0.135,0.188 10 true 5 6.385,0.281 6.531,0.469 0.146,0.188 10 true 6 6.625,0.854 6.76,1.042 0.135,0.188 10 true 1 6.677,1.51 6.813,1.708 0.135,0.198 10 true 7 6.448,2.385 6.583,2.583 0.135,0.198 10 true 8 6.094,2.542 6.229,2.74 0.135,0.198 10 true 9 4.74,2.573 4.958,2.76 0.219,0.188 10 true 10 4.281,2.385 4.5,2.573 0.219,0.188 10 false 11 5.365,1.365 5.583,1.552 0.219,0.188 10 true 12
*a Torque *b Bolt Tightening Order
*c Seal Washer - -


Torque:
Bolt (A), (B) : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt (C) : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11336A 4.INSTALL TIMING GEAR COVER INSULATOR

a.

Install the timing gear cover insulator to the timing chain cover assembly.


Hide 16620D 5.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 82121 6.INSTALL ENGINE WIRE

a.

Install the engine wire to the timing chain cover assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17342D 7.INSTALL NO. 2 AIR HOSE

a.

Install the No. 2 air hose to the turbocharger sub-assembly and tighten the hose clamp.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 17361J 8.INSTALL NO. 1 AIR TUBE

a.

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Install the No. 1 air tube to the No. 2 air hose, No. 3 air hose and tighten the hose clamp.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 88310 9.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16361A 10.INSTALL FAN AND GENERATOR V BELT

Hide 51410 11.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 13.INSTALL FRONT WHEELS