Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  P057111  Brake Switch "A" Circuit Short to Ground  


DESCRIPTION

The skid control ECU (brake actuator assembly) inputs the stop light signal and brake operation condition.

When the brake pedal is depressed and the stop light switch signal is not input, this DTC is output.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057111 Brake Switch "A" Circuit Short to Ground Either of the following is detected:
·

When the +BS terminal voltage is 9.5 V or higher and the brake pedal load sensing switch is ON, the stop light switch signal is input continuously for 2 seconds or more with the master cylinder pressure at 2 MPa (20.4 kgf/cm2) or higher and the deceleration calculated from the vehicle speed at 0.2 G or higher.

·

After a master cylinder pressure of more than 1.764 MPa (18.0 kgf/cm2) is detected for 5 seconds or more continuously at a vehicle speed below 3 km/h (2 mph) with the stop light switch assembly off, the master cylinder pressure exceeds 1.764 MPa (18.0 kgf/cm2) for 1 second or more continuously while and the stop light switch assembly signal is not received when the vehicle decelerates from over 35 km/h (22 mph) to 3 km/h (2 mph).


·

Stop light switch assembly

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION



PROCEDURE

1.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Gasoline Model RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and stop light switch assembly before inspecting the input signals and other related parts.


Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SW)

NG

14.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (STOP LIGHT SW)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly
(STP terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP


Chassis > Brake > Data List
Tester Display
Stop Light SW
50003 435 59

b.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays OFF / ON according to brake pedal operation.



c.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch turn on.


Result:
Result Proceed to
OK A
NG (The stop light switch assembly does not turn on) B



A

4.CLEAR DTC

B

6.CHECK VEHICLE SPECIFICATION
4.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Result:
Result Proceed to
P057111 is not output A
P057111 is output B



A

B

6.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for 3 Door A
for 5 Door B



A

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

B

11.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A108-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A108-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

8.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CLEAR DTC
a.

Reconnect the A108 skid control ECU (brake actuator assembly) connector.


b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

c.

Press the DTC clear button.


d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Result:
Result Proceed to
P057111 is not output A
P057111 is output B



A

10.INSPECT STOP LIGHT SWITCH ASSEMBLY

B

10.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A36-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

12.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CLEAR DTC
a.

Reconnect the A36 skid control ECU (brake actuator assembly) connector.


b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

c.

Press the DTC clear button.


d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Result:
Result Proceed to
P057111 is not output A
P057111 is output B



A

14.INSPECT STOP LIGHT SWITCH ASSEMBLY

B

14.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY