The main body ECU (multiplex network body ECU) receives door key cylinder lock or unlock switch signals from the front door lock assembly (for Driver Door). The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*
*: w/ Entry and Start System
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock Switch Status by a Mechanical Key (D/P Door) | Driver door key-linked switch lock signal | OFF or ON | OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position |
- |
| Door Unlock Switch Status by a Mechanical Key (D Door) | Driver door key-linked switch unlock signal | OFF or ON | OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position |
- |
| Tester Display |
|---|
| Door Lock Switch Status by a Mechanical Key (D/P Door) |
| Door Unlock Switch Status by a Mechanical Key (D Door) |
On the GTS screen, ON or OFF is displayed for each item according to the table above.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
for 5 Door: Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK (for 5 Door)>INSPECTION
for 3 Door: Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK (for 3 Door)>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
for 5 Door: Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK (for 5 Door)>REMOVAL
for 3 Door: Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK (for 3 Door)>REMOVAL
Disconnect the L11 front door lock assembly LH connector.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L11-9 (L) - H4-28 (L2) | Always | Below 1 Ω |
| L11-10 (UL) - H4-4 (UL3) | Always | Below 1 Ω |
| L11-7 (E) - Body ground | Always | Below 1 Ω |
| L11-9 (L) or H4-28 (L2) - Other terminals and body ground | Always | 10 kΩ or higher |
| L11-10 (UL) or H4-4 (UL3) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K11 front door lock assembly RH connector.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K11-6 (L) - H4-28 (L2) | Always | Below 1 Ω |
| K11-5 (UL) - H4-4 (UL3) | Always | Below 1 Ω |
| K11-8 (E) - Body ground | Always | Below 1 Ω |
| K11-6 (L) or H4-28 (L2) - Other terminals and body ground | Always | 10 kΩ or higher |
| K11-5 (UL) or H4-4 (UL3) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG