Refer to Step 9 for the front door scuff plate (w/ Plate) removal procedure.
64330D
1.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
Disengage the hooks.
|
Remove in this Direction |
Disengage the guides to remove the package tray trim panel assembly as shown in the illustration.
58410B
2.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)
Remove the deck board assembly.
64771G
3.REMOVE SPARE WHEEL COVER
Remove the spare wheel cover.
64777J
4.REMOVE SPARE WHEEL CUSHION (for Compact Spare Tire)
Remove the spare wheel cushion.
64993
5.REMOVE REAR DECK FLOOR BOX (w/ Repair Kit)
Remove the clip and rear deck floor box.
6.REMOVE REAR SEAT ASSEMBLY
67914B
7.REMOVE FRONT DOOR SCUFF PLATE LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claws and guides to remove the front door scuff plate LH as shown in the illustration.
67913B
8.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
67914B
9.REMOVE FRONT DOOR SCUFF PLATE LH (w/ Plate)
Perform this procedure only when replacement of the front door scuff plate LH is necessary.
Remove the front door scuff plate LH.
67913B
10.REMOVE FRONT DOOR SCUFF PLATE RH (w/ Plate)
Perform this procedure only when replacement of the front door scuff plate RH is necessary.
Use same procedure as for the LH side.
62112
11.REMOVE COWL SIDE TRIM BOARD LH
|
Remove in this Direction |
Remove the clip.
Disengage the clip to remove the cowl side trim board LH as shown in the illustration.
62111C
12.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
62312B
13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
14.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62212
15.REMOVE FRONT PILLAR GARNISH LH
62211
16.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
76974F
17.REMOVE REAR UNDER SIDE COVER LH (for HV Model)
|
Remove in this Direction |
Remove the clip.
Disengage the clips and guides to remove the rear under side cover LH as shown in the illustration.
76973F
18.REMOVE REAR UNDER SIDE COVER RH (for HV Model)
|
Remove in this Direction |
Remove the 2 clips.
Disengage the clips and guides to remove the rear under side cover RH as shown in the illustration.
67918F
19.REMOVE REAR DOOR SCUFF PLATE INSIDE LH
Disengage the claws and guides to remove the rear door scuff plate inside LH as shown in the illustration.
| *A | for Gasoline Model | *B | for HV Model |
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
67917F
20.REMOVE REAR DOOR SCUFF PLATE INSIDE RH
Use the same procedure as for the LH side.
62332A
21.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
62331A
22.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the RH side.
73233
23.REMOVE LAP BELT OUTER ANCHOR COVER
Use the same procedure as for the opposite side.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for 5 Door)>REMOVAL
73220
24.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
73210
25.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62414A
26.REMOVE CENTER PILLAR LOWER GARNISH LH
|
Place Hands Here |
|
Remove in this Direction |
Disengage the claws, guides and clips to remove the center pillar lower garnish LH as shown in the illustration.
62413A
27.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
62412B
28.REMOVE CENTER PILLAR UPPER GARNISH LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the 2 clips.
Disengage the clip and guides to remove the center pillar upper garnish LH as shown in the illustration.
62411B
29.REMOVE CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
64716D
30.REMOVE DECK TRIM REAR COVER
|
Place Hands Here |
|
Remove in this Direction |
Disengage the claws and guides to remove the deck trim rear cover as shown in the illustration.
81330
31.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
71304C
32.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
Loosen the bolt to remove the rear seatback hinge sub-assembly LH.
71303C
33.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure as for the RH side.
64715C
34.REMOVE DECK TRIM SIDE COVER LH
| *a | Protective Tape |
|
Remove in this Direction |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and guide to remove the deck trim side cover LH as shown in the illustration.
64714C
35.REMOVE DECK TRIM SIDE COVER RH
Use the same procedure as for the LH side.
64740C
36.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
|
Remove in this Direction |
Remove the 2 screws.
Disengage the claws, clips and guide to remove the deck trim side panel assembly LH as shown in the illustration.
64730B
37.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
73370E
38.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
73360D
39.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62472A
40.REMOVE ROOF SIDE INNER GARNISH LH
|
Remove in this Direction |
Disengage the clips to remove the roof side inner garnish LH as shown in the illustration.
62471A
41.REMOVE ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
74320
42.REMOVE VISOR ASSEMBLY LH
74310
43.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348C
44.REMOVE VISOR HOLDER
Use the same procedures for the opposite side.
|
Turn in this Direction |
|
Remove in this Direction |
Turn the visor holder counterclockwise approximately 45° and pull it out as shown in the illustration.
|
Remove in this Direction |
Disengage the claws to remove the base as shown in the illustration.
74612
45.REMOVE ASSIST GRIP COVER
Use the same procedure for all assist grip sub-assemblies.
| *a | Cutout |
Insert SST into the cutout of the assist grip cover as shown in the illustration.
To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.
| *a | 30 to 45° |
|
Remove in this Direction |
Pull SST as shown in the illustration to disengage the claw.
To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.
Remove the assist grip cover.
Use the same procedures for the opposite side.
74610A
46.REMOVE ASSIST GRIP SUB-ASSEMBLY
Use the same procedures for the opposite side.
|
Remove in this Direction |
Disengage the clips to remove the assist grip sub-assembly as shown in the illustration.
Remove the 2 clips from the vehicle body.
74630E
47.REMOVE REAR ASSIST GRIP ASSEMBLY LH (w/ Assist Grip)
Use the same procedure as for the assist grip sub-assembly.
74620C
48.REMOVE REAR ASSIST GRIP ASSEMBLY RH (w/ Assist Grip)
Use the same procedure as for the assist grip sub-assembly.
49.REMOVE COAT HOOK (w/o Assist Grip)
Use the same procedures for the opposite side.
| *a | Protective Tape |
Using a clip remover with its tip wrapped in protective tape, disengage the clip to remove the coat hook.
81260A
50.REMOVE MAP LIGHT ASSEMBLY
81240J
51.REMOVE ROOM LIGHT ASSEMBLY (for TMC Made)
81340
52.REMOVE VANITY LIGHT ASSEMBLY (w/ Vanity Light)
86466E
53.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
86466D
54.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense 2)
63339A
55.REMOVE ROOF HEADLINING SERVICE HOLE COVER
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a molding remover B, disengage the claws and guides to remove the roof headlining service hole cover as shown in the illustration.
63311C
56.REMOVE ROOF HEADLINING (for Normal Roof)
for Front Pillar LH Side:
Disconnect the 2 connectors.
Using a clip remover, disengage the clamps.
for Front Pillar RH Side:
Disconnect the connector.
Using a clip remover, disengage the clamps.
for Windshield Glass Side:
for TMC Made:
Disconnect the 2 connectors.
for TMMF Made with EC Mirror:
Disconnect the 2 connectors.
for TMMF Made with Toyota Safety Sense 2:
Disconnect the 3 connectors.
for TMMF Made with Toyota Safety Sense 2 and EC Mirror:
Disconnect the 4 connectors.
for Rear Pillar RH Side:
Disconnect the connector.
for Roof Rear Side:
Disconnect the connector.
Remove the bolt.
Disengage the guide to separate the ground wire.
for TMC Made:
Using a clip remover, remove the 2 clips.
Disengage the guides to remove the roof headlining.
for TMMF Made:
Using a clip remover, remove the 4 clips.
Disengage the guides to remove the roof headlining.
|
Remove in this Direction |
Turn the roof headlining diagonally and bend slightly to remove it from the back door as shown in the illustration.
Make sure that wrinkles do not form in the roof headlining during removal.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
63311C
57.REMOVE ROOF HEADLINING (for Panoramic Moon Roof)
for Front Pillar LH Side:
Disconnect the 2 connectors.
Using a clip remover, disengage the clamps.
for Front Pillar RH Side:
Disconnect the connector.
Using a clip remover, disengage the clamps.
for Windshield Glass Side:
Disconnect the 2 connectors.
for Rear Pillar RH Side:
Disconnect the connector.
for Roof Rear Side:
Disconnect the connector.
Remove the bolt.
Disengage the guide to separate the ground wire.
Using a clip remover, remove the 2 clips.
| *a | Fastener | *b | Guide |
Disengage the guides and fasteners to remove the roof headlining.
|
Remove in this Direction |
Turn the roof headlining diagonally and bend slightly to remove it from the back door as shown in the illustration.
Make sure that wrinkles do not form in the roof headlining during removal.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.