2005-2008 Yaris · Service Manual BRAKE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Nov 2005


CHECK DLC3
H100769E16
  1. The ECU uses ISO 15765-4 for communication.
    The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

    Symbols (Terminal No.)
    Terminal Description
    Condition
    Specified Condition
    SIL (7) - SG (5)
    Bus "+" line
    During transmission
    Pulse generation
    CG (4) - Body ground
    Chassis ground
    Always
    Below 1 Ω
    SG (5) - Body ground
    Signal ground
    Always
    Below 1 Ω
    BAT (16) - Body ground
    Battery positive
    Always
    10 to 14 V
    CANH (6) - CANL (14)
    HIGH-level CAN bus line
    Ignition switch off*
    54 to 69 Ω
    CANH (6) - CG (4)
    HIGH-level CAN bus line
    Ignition switch off*
    200 Ω or more
    CANL (14) - CG (4)
    LOW-level CAN bus line
    Ignition switch off*
    200 Ω or more
    CANH (6) - BAT (16)
    HIGH-level CAN bus line
    Ignition switch off*
    6 kΩ or more
    CANL (14) - BAT (16)
    LOW-level CAN bus line
    Ignition switch off*
    6 kΩ or more

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

    If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

    HINT:
    Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

    1. A107926E08
    2. If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
    3. If communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.


DIAGNOSIS
If the skid control ECU detects a malfunction, the ABS, VSC, BRAKE warning lights and SLIP indicator light come on in accordance with the trouble area, to warn the driver.
The table below indicates which lights come on when there are malfunctions in particular functions.
○: Light ON, -: Light OFF
C121697E01
Item / Trouble Area
ABS
EBD
BA (Brake Assist)
TRC
VSC
ABS warning light
○
○
○
-
-
BRAKE warning light
-
○
-
-
-
VSC warning light
○
○
○
○
○
SLIP indicator light
○
○
○
○
○

HINT:
  1. The DTCs can be read by connecting SST (09843-18040) between the TC and CG terminals of the DLC3 and observing the blinking pattern of the ABS and VSC warning lights, or by using an intelligent tester (Click here).
  2. This system has a sensor signal check function (Click here).


WARNING LIGHT CHECK
  1. Release the parking brake lever.

    NOTICE:
    Before releasing the parking brake lever, set chocks to hold the vehicle for safety.

    HINT:
    When the parking brake is applied or the brake fluid level is low, the BRAKE warning light comes on.

  2. When the ignition switch is turned on (IG), check that the ABS, VSC, BRAKE warning lights and SLIP indicator light come on and go off in about 3 seconds.

    HINT:
    1. If the warning and indicator lights do not illuminate, confirm whether the bulbs have burned out.
    2. If the warning light remains on, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are instructed in the sections listed in the table below.
      Section Title
      See Page
      ABS Warning Light Remains ON
      Click here
      VSC Warning Light Remains ON
      Click here
      BRAKE Warning Light Remains ON
      Click here
      SLIP Indicator Light Remains ON
      Click here

← TERMINALS OF ECU (from Nov 2005)DTC CHECK / CLEAR (from Nov 2005) →