2005-2008 Yaris · Service Manual BRAKE

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

If any of the following conditions are detected, the BRAKE warning light remains on:
  1. The ECU connectors are disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. The EBD is defective.

WIRING DIAGRAM

C129350E01
C129351E01

INSPECTION PROCEDURE

NOTICE:
When replacing the ABS and TRACTION actuator, perform zero point calibration (Click here).


1. PREPARE FOR INSPECTION
  1. Check that both of the following conditions are satisfied.

    1. The brake fluid level in the brake master cylinder reservoir is correct.
    2. The parking brake is released.

    HINT:
    When the ABS warning light remains illuminated, repair the malfunctions in the ABS system first.


NEXT


2. CHECK DTC
  1. Check if any ABS DTCs are output (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


3. CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CAN COMMUNICATION SYSTEM
A


4. CHECK CONNECTOR CONNECTION CONDITION
  1. Check if the skid control ECU connector is connected securely.

    OK:
    The connector is connected securely.



NG
CONNECT CONNECTOR CORRECTLY
OK


5. CHECK PARKING BRAKE SWITCH ASSEMBLY

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the "Parking Brake SW" in the DATA LIST.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

    DATA LIST: ABS/VSC/TRC 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released

  1. Check that "ON" and "OFF" are properly indicated on the tester display when the parking brake lever is operated.

    OK:
    Tester display changes in accordance with the parking brake lever operation.



NG
Go to step 9
OK


6. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

  1. C129358E01
    Remove the reservoir tank cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance.

    HINT:
    A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake fluid level.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A36-1 - A36-2
    Float up (Switch OFF)
    10 kΩ or higher
    A36-1 - A36-2
    Float down (Switch ON)
    Below 1 Ω

    HINT:
    If the result is as specified, adjust the brake fluid level to the MAX level after measuring the resistance.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

  1. C129352E01
    Disconnect the skid control ECU connector.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A39-20 (LVL2) - A36-2
    Below 1 Ω
    A39-20 (LVL2) - Body ground
    10 kΩ or higher
    A36-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT COMBINATION METER
  1. Inspect the combination meter (Click here).



NG
REPLACE COMBINATION METER
OK

REPLACE ABS AND TRACTION ACTUATOR

9. INSPECT PARKING BRAKE SWITCH ASSEMBLY

  1. C129357E01
    Disconnect the parking brake switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D21-1 - Body ground
    Parking brake switch ON
    (Switch pin released)
    Below 1 Ω
    D21-1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY
OK


10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY)

  1. C120360E01
    Disconnect connector 4C of the main body ECU (Click here).

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    4C-2 (PKB) - D21-1
    Below 1 Ω
    4C-2 (PKB) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← VSC Warning Light does not Come ON (from Nov 2005)Brake Warning Light does not Come ON (from Nov 2005) →