INSTALLATION
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL SKID CONTROL SENSOR |
Wipe the sealant off the skid control sensor installation surface using white gasoline.
- NOTICE:
- Keep the sensor rotor free of foreign matter.
Install the skid control sensor onto the rear axle hub in the highest possible installation position.

- HINT:
- The distance between the installation holes should be larger on the upper side than the lower side.
Using SST and a press, install a new skid control sensor into the rear axle hub until it is flush with the end.

- SST
- 09214-76011
- NOTICE:
- Do not use a hammer when installing.
- Check for any foreign matter on the sensor probe.
- Press the skid control sensor in slowly without turning it.
- Do not use a hammer when installing.
| 2. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY |
![]() ![]() |
for Rear Drum Brake:
Install the axle hub and bearing onto the axle beam with the 4 bolts.
- Torque:
- 90 N*m{ 918 kgf*cm , 67 ft.*lbf }
for Rear Disc Brake:
Install the dust cover and the axle hub and bearing onto the axle beam with the 4 bolts.
- Torque:
- 90 N*m{ 918 kgf*cm , 67 ft.*lbf }
| 3. INSPECT REAR AXLE HUB BEARING |
Remove the rear wheel.
for Rear Drum Brake:
Remove the rear brake drum (Click here).
for Rear Disc Brake:
Disconnect the parking brake cable (Click here).
Separate the disc brake cylinder (Click here).
Remove the disc brake pad.
Remove the disc brake cylinder mounting (Click here).
Remove the rear disc (Click here).
Inspect the axle hub and bearing backlash.

Using a dial indicator, check the backlash near the center of the axle hub.
- Maximum:
- 0.05 mm (0.0020 in.)
Inspect the axle hub and bearing runout.

Using a dial indicator, check the runout of the surface of the axle hub.
- Maximum:
- 0.07 mm (0.0028 in.)
for Rear Drum Brake:
Install the rear brake drum.
Adjust the rear drum brake shoe clearance (Click here).
for Rear Disc Brake:
Install the rear disc (Click here).
Install the disc brake cylinder mounting (Click here).
Install the disc brake pad.
Install the disc brake cylinder (Click here).
Connect the parking brake cable (Click here).
Install the rear wheel.
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 4. CONNECT SKID CONTROL SENSOR WIRE |
![]() ![]() |
Connect the skid control sensor wire connector.
| 5. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake) |
| 6. ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Rear Drum Brake) |
![]() ![]() |
Provisionally install the 2 hub nuts.
Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.
Using a screwdriver, release the adjuster 12 notches.
Install the hole plug.
| 7. INSTALL REAR DISC (for Rear Disc Brake) |
![]() ![]() |
Align the matchmarks of the disc and axle hub and install the disc.
- NOTICE:
- When replacing the disc, select the position that gives the minimum disc runout.
| 8. INSTALL REAR DISC BRAKE CYLINDER MOUNTING (for Rear Disc Brake) |
![]() ![]() |
Install the disc brake cylinder mounting onto the axle beam with the 2 bolts.
- Torque:
- 57 N*m{ 585 kgf*cm , 42 ft.*lbf }
| 9. INSTALL REAR DISC BRAKE PAD KIT (PAD ONLY) (for Rear Disc Brake) |
![]() ![]() |
Install the 2 disc brake pads onto the disc brake cylinder mounting.
- NOTICE:
- There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.
| 10. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY (for Rear Disc Brake) |
![]() ![]() |
Install the disc brake cylinder with the 2 bolts.
- Torque:
- 34 N*m{ 350 kgf*cm , 25 ft.*lbf }
| 11. CONNECT PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake) |
![]() ![]() |
Install the casing cap clip onto the rear disc brake cylinder guide.
Connect the cable end to the rear disc brake cylinder operation lever.
| 12. INSTALL REAR WHEEL |
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 14. CHECK ABS SENSOR SIGNAL (w/o VSC) |
| 15. CHECK VSC SENSOR SIGNAL (w/ VSC) |








